Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) › 2019.02–2021.07
RM35X0E _56 Audio / Visual / Telematics _078377 AUDIO / VIDEO _0383454 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Mute Signal Circuit between Radio Receiver and Telematics Transceiver  


DESCRIPTION

The DCM (telematics transceiver) sends a mute signal to the radio receiver assembly.

The radio receiver assembly controls the volume according to the mute signal from the DCM (telematics transceiver).

WIRING DIAGRAM

E350600E08
5,2 6.688,2.198 1.688,0.198 10 false Radio Receiver Assembly 5,1.802 5.458,2 0.458,0.198 10 false O11 0.979,2 3.094,2.25 2.115,0.25 10 false DCM (Telematics Transceiver) 0.979,1.802 1.438,2 0.458,0.198 10 false N74 1.531,1.052 2.146,1.25 0.615,0.198 10 false MUTE 5.219,1.052 5.833,1.25 0.615,0.198 10 false TMUT 5,0.917 5.156,1.115 0.156,0.198 10 false 8 2.083,0.917 2.323,1.167 0.24,0.25 10 false 17

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for audio and visual system.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)>PRECAUTION


PROCEDURE

1.CHECK DCM (TELEMATICS TRANSCEIVER)
a.
E366538C16
1.5,0.802 1.896,1.052 0.396,0.25 1.396,1.896 1.021,0.906 true 0.188,0.125 0.5,0.323 0.313,0.198 10 false *a 0.792,0.708 1.302,0.917 0.51,0.208 10 false MUTE 1.594,0.844 1.906,1.042 0.313,0.198 10 false N74
*a Component with harness connected
(DCM [Telematics Transceiver])


Remove the DCM (telematics transceiver) with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for LHD)>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N74-17 (MUTE) - Body ground Ignition switch ACC
Audio system playing
→ Emergency call mode
3.5 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])
2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])
a.

Disconnect the O11 radio receiver assembly connector.


b.

Disconnect the N74 DCM (telematics transceiver) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-8 (TMUT) - N74-17 (MUTE) Always Below 1 Ω
O11-8 (TMUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO RECEIVER ASSEMBLY
a.

Disconnect the DCM (telematics transceiver) connector.


b.
E416150C01
1.479,0.719 1.969,1.01 0.49,0.292 1.99,2.083 2.167,2.583 true 0.188,0.167 0.354,0.323 0.167,0.156 10 false *a 2.031,2.635 2.458,2.792 0.427,0.156 10 false MUTE 1.552,0.781 1.958,1.01 0.406,0.229 10 false N74
*a Front view of wire harness connector
(to DCM [Telematics Transceiver])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N74-17 (MUTE) - Body ground Ignition switch ACC 3.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE RADIO RECEIVER ASSEMBLY