Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › EGR VALVE (w/ EGR Cooler)
RM35X0E _51 Engine / Hybrid System _079220 1GD-FTV EMISSION CONTROL _0384171 EGR VALVE(w/ EGR Cooler) G

1GD-FTV EMISSION CONTROL  EGR VALVE(w/ EGR Cooler)  INSPECTION  


PROCEDURE

Hide 25800 1.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY

a.

Visually check the electric EGR control valve assembly for deposits.

NOTICE:
·

When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.

·

Do not forcibly open the valve as it may be damaged or deformed.

·

When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto this part or soaking the part in solvent may damage the part.




b.
A344445C01
2.729,3.479 2.583,3 2.583,3 2.417,3 true 2.729,3.927 2.417,4.344 2.417,4.344 2.25,4.344 true 1.219,3.594 1.031,3.042 1.031,3.042 0.865,3.042 true 0.854,4.385 1.167,4.542 0.313,0.156 10 false *c 2.604,4.385 2.917,4.542 0.313,0.156 10 false *d 0.698,2.938 1.01,3.094 0.313,0.156 10 false *a 2.24,2.896 2.552,3.052 0.313,0.156 10 false *b 2.094,4.25 2.406,4.406 0.313,0.156 10 false *b
*a Seal Ring End
*b Gap
*c CORRECT
*d INCORRECT


Hold the electric EGR control valve assembly up to a light, and then from the side indicated by the arrow in the illustration, visually check that there is no gap between the valve and body.

OK:

No light passes through (there is no gap between the valve and body).


HINT:

Light passes through the part even if the valve is completely closed as there is an opening in the seal ring of the valve, this is not a problem.


If light passes through (there is a gap between the valve and body), replace the electric EGR control valve assembly.


Hide 25630 2.INSPECT NO. 2 EGR VALVE ASSEMBLY

NOTICE:
·

Do not forcibly open the valve as it may be damaged or deformed.

·

When cleaning the No. 2 EGR valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto this part or soaking the part in solvent may damage the part.



a.
A344446

for Single Actuator EGR Bypass Valve:

When a vacuum of 69.7 kPa (523 mmHg, 20.6 in.Hg) is applied to the diaphragm chamber, check that the valve turns and air flows out.


b.

for Double Actuator EGR Bypass Valve:

Connect the 2 vacuum pumps as shown in the illustration. First apply vacuum of 75 kPa (0.8 kgf/cm2, 11 psi) to the diaphragm closer to the EGR valve. This will cause the actuator rod to move, which causes the EGR valve to move. Then, apply vacuum of 75 kPa (0.8 kgf/cm2, 11 psi) to the diaphragm on the outer side. This will cause the actuator rod to move further, which also causes the EGR valve to move further. Check that the valve is fully open.

A442607C01
0.906,1.604 1.219,1.76 0.313,0.156 10 false *a 4.625,0.417 4.938,0.573 0.313,0.156 10 false *a
*a Vacuum - -



c.

Maintaining the above conditions, check that there are no leaks and the valve does not return.


d.

Check that the valve does not have heavy carbon deposits and is not stuck.

If necessary, replace the No. 2 EGR valve assembly.