Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › CYLINDER BLOCK
RM35X0E _51 Engine / Hybrid System _079219 1GD-FTV ENGINE MECHANICAL _0384431 CYLINDER BLOCK A

1GD-FTV ENGINE MECHANICAL  CYLINDER BLOCK  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pin unless it is being replaced.


a.

Remove the straight pin from the cylinder block sub-assembly.


b.

Using a plastic-faced hammer, tap in a new straight pin to the cylinder block sub-assembly.

A337482C01
0.813,0.021 1.125,0.177 0.313,0.156 10 false *a 4.26,0.021 4.573,0.177 0.313,0.156 10 false *b 0.24,2.719 0.552,2.875 0.313,0.156 10 false *c 0.677,3.594 0.99,3.75 0.313,0.156 10 false *d 1.604,2.729 1.917,2.885 0.313,0.156 10 false *e 2.052,3.323 2.365,3.479 0.313,0.156 10 false *i 2.969,2.708 3.281,2.958 0.313,0.25 10 false *g 4.292,2.729 4.604,2.917 0.313,0.188 10 false *h 6.76,2.531 7.063,2.844 0.302,0.313 10 false *j 3.427,3.229 3.74,3.385 0.313,0.156 10 false *f 4.771,3.365 5.083,3.521 0.313,0.156 10 false *d 0.698,2.052 0.854,2.25 0.156,0.198 10 false A 2.771,1.24 2.927,1.438 0.156,0.198 10 false A 2.323,2.115 2.479,2.313 0.156,0.198 10 false B 2.052,2.333 2.208,2.531 0.156,0.198 10 false B 1.115,0.708 1.292,0.885 0.177,0.177 10 true B 3.417,2.438 3.573,2.635 0.156,0.198 10 false C 4.813,1.24 5,1.417 0.188,0.177 10 true C 5.594,1.24 5.792,1.417 0.198,0.177 10 true C 4.771,2.26 4.927,2.458 0.156,0.198 10 false D 4.26,2.01 4.417,2.208 0.156,0.198 10 false D 6.167,2.021 6.323,2.219 0.156,0.198 10 false D
*a Engine Front Side *b Engine Rear Side
*c 36 mm (1.42 in.) *d 10 mm (0.394 in.)
*e 18 mm (0.709 in.) *f 6.0 mm (0.236 in.)
*g 11 mm (0.433 in.) *h 22 mm (0.866 in.)
*i 8.0 mm (0.315 in.) *j Protrusion Height


Standard Protrusion Height:
Item Specified Condition
Straight Pin A 18 to 20 mm (0.709 to 0.787 in.)
Straight Pin B 8.0 to 10 mm (0.315 to 0.394 in.)
Straight Pin C 4.0 to 6.0 mm (0.157 to 0.236 in.)
Straight Pin D 10 to 12 mm (0.394 to 0.472 in.)



Hide 2.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


a.

Remove the ring pin from the cylinder block sub-assembly.


b.

Using a plastic-faced hammer, tap in a new ring pin to the cylinder block sub-assembly.

Standard protrusion height:

5.5 to 7.5 mm (0.217 to 0.295 in.)


A337483C01
6.073,1.219 6.385,1.375 0.313,0.156 10 false *a
*a Protrusion Height - -