Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ VSC OFF Switch) › 2019.02–2019.06
RM35X0E _54 Brake _078667 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0385049 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/ VSC OFF Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/ VSC OFF Switch)  C13807E  Stop Lamp Relay Actuator Stuck On  


DESCRIPTION

When any of the following conditions are met, the skid control ECU (brake actuator assembly) sets the drive output (STPO) ON which operates the stop light control relay (stop light switch assembly) and turns on the stop lights.

Illumination Conditions:
·

Pre-collision brake is operating.

·

The dynamic radar cruise control system is operating and is applying the brakes.*

·

Secondary collision brake is operating.*

·

The parking brake is engaged while the vehicle is being driven.


*: w/ Pre-collision System

DTC No. Detection Item DTC Detection Condition Trouble Area
C13807E Stop Lamp Relay Actuator Stuck On When the voltage at the +BS terminal is between 10 V or more and the STOP LP relay (stop light relay) drive output (STPO) is off, the signal at the STP2 terminal is different from the input signal at the STP terminal for 5 seconds or more.
·

Wire harness or connector

·

STOP LP relay (stop light relay)

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C413715E02
2.99,0.708 4.677,0.906 1.688,0.198 10 false to Each ECU 0.854,2.438 2.688,2.656 1.833,0.219 10 false Stop Light Switch Assembly 5.198,4.354 6.729,4.76 1.531,0.406 10 false Skid Control ECU (Brake Actuator Assembly) 2.531,4.927 4.219,5.125 1.688,0.198 10 false from IG Circuit 2.531,3.958 4.354,4.188 1.823,0.229 10 false STOP LP (Stop Light Relay) 1.813,5.875 3.5,6.073 1.688,0.198 10 false from Battery 1.333,5.104 3.021,5.302 1.688,0.198 10 false IG2 NO. 1 0.833,6.063 2.521,6.26 1.688,0.198 10 false STOP 5.563,1.833 5.958,2.042 0.396,0.208 10 false STP 5.563,2.677 5.958,2.885 0.396,0.208 10 false STP2 5.563,3.417 5.958,3.625 0.396,0.208 10 false STPO 5.208,4.177 5.604,4.385 0.396,0.208 10 false A28 0.865,2.281 1.26,2.49 0.396,0.208 10 false M1 5.323,1.833 5.635,2.031 0.313,0.198 10 false 9 5.302,2.688 5.615,2.885 0.313,0.198 10 false 24 5.354,3.427 5.667,3.625 0.313,0.198 10 false 3 1.052,1.844 1.365,2.042 0.313,0.198 10 false 2 2.365,1.844 2.677,2.042 0.313,0.198 10 false 1 2.729,2.688 3.042,2.885 0.313,0.198 10 false 5 3.406,2.198 3.719,2.396 0.313,0.198 10 false 4 3.917,2.698 4.229,2.896 0.313,0.198 10 false 3 2.729,3.406 3.042,3.604 0.313,0.198 10 false 2 3.917,3.417 4.229,3.615 0.313,0.198 10 false 1 2.656,6.802 4.344,7 1.688,0.198 10 false to Stop Light Circuit 2.135,1.823 2.448,2.021 0.313,0.198 10 false L 1.26,1.823 1.573,2.021 0.313,0.198 10 false B

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ VSC OFF Switch)>UTILITY



HINT:

When DTC P057111, P057112 and/or P057113 are output together with DTC C13807E, inspect and repair the trouble areas indicated by DTC P057111, P057112 and/or P057113 first.

P057111: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ VSC OFF Switch)>P057111

P057112: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ VSC OFF Switch)>P057112

P057113: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ VSC OFF Switch)>P057113


PROCEDURE

1.CHECK STOP LIGHT ILLUMINATION STATUS
a.

With the brake pedal released, check the illumination status of the brake lights.


Result:
Result Proceed to
The stop lights are illuminated. A
The stop lights are not illuminated. B



A

2.CHECK HARNESS AND CONNECTOR (SPOT LIGHT RELAY - BRAKE ACTUATOR ASSEMBLY)

B

4.CHECK STOP LIGHT OPERATION
2.CHECK HARNESS AND CONNECTOR (SPOT LIGHT RELAY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A28 skid control ECU (brake actuator assembly) connector.


c.

Remove the STOP LP relay (stop light relay) from the No. 1 engine room relay block and No. 1 junction block.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 or A28-3 (STPO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STOP LIGHT RELAY
a.

Turn the ignition switch off.


b.

Remove the STOP LP relay (stop light relay) from the No. 1 engine room relay block and No. 1 junction block.


c.

Inspect the STOP LP relay (stop light relay).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>RELAY>ON-VEHICLE INSPECTION

OK:

The STOP LP relay (stop light relay) is normal.


Result:
Result
OK
NG




OK

NG

REPLACE STOP LIGHT RELAY

4.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed.

OK:

The stop lights illuminate.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY - BRAKE ACTUATOR ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY - BRAKE ACTUATOR ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A28 skid control ECU (brake actuator assembly) connector.


c.

Remove the STOP LP relay (stop light relay) from the No. 1 engine room relay block and No. 1 junction block.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - A28-24 (STP2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A28 skid control ECU (brake actuator assembly) connector.


c.

Remove the STOP LP relay (stop light relay) from the No. 1 engine room relay block and No. 1 junction block.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - A28-9 (STP) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A28 skid control ECU (brake actuator assembly) connector.


c.

Remove the STOP LP relay (stop light relay) from the No. 1 engine room relay block and No. 1 junction block.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - A28-24 (STP2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - STOP LIGHT RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - STOP LIGHT RELAY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the M1 stop light switch assembly connector.


c.

Remove the STOP LP relay (stop light relay) from the No. 1 engine room relay block and No. 1 junction block.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M1-1 (L) - 4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR