Home › Vehicle Exterior › WIPER / WASHER › WASHER NOZZLE (for Rear Side)
RM35X0E _59 Vehicle Exterior _079320 WIPER / WASHER _0385309 WASHER NOZZLE(for Rear Side) G

WIPER / WASHER  WASHER NOZZLE(for Rear Side)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 85035R 1.INSPECT REAR WASHER NOZZLE SUB-ASSEMBLY (for Standard Roof)

a.

With the ignition switch to ON, check that the center stream of washer fluid sprays on the back door glass within the hatched area shown in the illustration.

Standard:

Washer fluid hits the back door glass in the area shown in the illustration.


B540171C01
1.75,0.521 1.979,0.76 false 2.146,2.25 1.917,2.156 false 3.208,2.271 3.5,2.167 false 1.563,0.406 1.875,0.563 0.313,0.156 10 false *a 3.042,2.198 3.354,2.354 0.313,0.156 10 false *b 3.563,0.302 3.813,0.458 0.25,0.156 10 false A 2.99,0.469 3.24,0.625 0.25,0.156 10 false B 4.979,0.813 5.229,0.969 0.25,0.156 10 false E 2.917,1.188 3.167,1.344 0.25,0.156 10 false D 1.74,2.052 2.052,2.208 0.313,0.156 10 false *c 3.323,0.76 3.573,0.917 0.25,0.156 10 false C 5.292,1.198 5.542,1.354 0.25,0.156 10 false F 2.781,1.615 3.031,1.771 0.25,0.156 10 false G 3.552,1.875 3.802,2.031 0.25,0.156 10 false H
*a Glass Edge *b Wiper Pattern
*c Center Line - -
V100145

Landing Area - -


Standard Measurement:
Area Measurement Area Measurement
A 118.2 mm (4.65 in.) B 82.8 mm (3.26 in.)
C 6.2 mm (0.244 in.) D 37.5 mm (1.48 in.)
E 10.5 mm (0.413 in.) F 42.1 mm (1.66 in.)
G 61.8 mm (2.43 in.) H 126.4 mm (4.98 in.)



Hide 85035R 2.INSPECT REAR WASHER NOZZLE SUB-ASSEMBLY (for High Roof)

a.

With the ignition switch to ON, check that the center stream of washer fluid sprays on the back door glass within the hatched area shown in the illustration.

Standard:

Washer fluid hits the back door glass in the area shown in the illustration.


B541416C01
1.688,0.542 1.885,0.729 false 3.24,2.313 3.469,2.177 false 1.823,2.125 2.115,2.25 false 1.521,0.458 1.833,0.615 0.313,0.156 10 false *a 3.052,2.24 3.365,2.396 0.313,0.156 10 false *b 1.656,2.031 1.969,2.188 0.313,0.156 10 false *c 3.417,0.271 3.573,0.427 0.156,0.156 10 false A 3.021,0.448 3.188,0.604 0.167,0.156 10 false B 3.656,0.677 3.823,0.833 0.167,0.156 10 true C 3.177,0.948 3.344,1.104 0.167,0.156 10 false D 5.042,0.781 5.208,0.938 0.167,0.156 10 false E 5.365,0.99 5.531,1.146 0.167,0.156 10 false F 2.885,1.333 3.052,1.49 0.167,0.156 10 false G 3.75,1.615 3.917,1.771 0.167,0.156 10 false H
*a Glass Edge *b Wiper Pattern
*c Center Line - -
V100145

Landing Area - -


Standard Measurement:
Area Measurement Area Measurement
A 116.8 mm (4.60 in.) B 84.6 mm (3.33 in.)
C 4.0 mm (0.157 in.) D 24.1 mm (0.949 in.)
E 7.3 mm (0.287 in.) F 26.9 mm (1.06 in.)
G 69.5 mm (2.74 in.) H 123.4 mm (4.86 in.)