Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2019.02–2021.07
RM35X0E _56 Audio / Visual / Telematics _078377 AUDIO / VIDEO _0385463 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Data Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the radio and display receiver assembly via this circuit.

WIRING DIAGRAM

E360461E47
1.344,0.5 1.521,0.677 0.177,0.177 10 false 9 0.875,1.458 1.49,1.656 0.615,0.198 10 false UDO+ 0.906,2.219 1.521,2.417 0.615,0.198 10 false UJSS 5.906,2.219 6.521,2.417 0.615,0.198 10 false USG1 5.906,1.458 6.521,1.656 0.615,0.198 10 false US1+ 5.906,0.656 6.521,0.854 0.615,0.198 10 false US1- 0.438,2.646 1.052,2.844 0.615,0.198 10 false N129 0.438,2.802 1.594,3.281 1.156,0.479 10 false No. 1 Stereo Jack Adapter Assembly 2.479,3.271 5.083,3.5 2.604,0.229 10 false : Data Signal (USB Communication Line) 0.24,3.375 1.458,3.646 1.219,0.271 10 false *: Shielded 5.813,2.635 6.427,2.833 0.615,0.198 10 false N128 5.802,2.802 7,3.271 1.198,0.469 10 false Radio and Display Receiver Assembly 5.729,0.542 5.906,0.719 0.177,0.177 10 false 2 1.333,1.323 1.51,1.5 0.177,0.177 10 false 10 1.354,2.094 1.531,2.271 0.177,0.177 10 false 12 5.75,2.115 5.927,2.292 0.177,0.177 10 false 5 5.74,1.323 5.917,1.5 0.177,0.177 10 false 3 0.906,0.656 1.521,0.854 0.615,0.198 10 false UDO- 3.563,1.802 4.781,2.073 1.219,0.271 10 false *

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.
E360495C78
1.542,2.198 1.979,2.49 0.438,0.292 1.542,0.208 1.958,0.479 0.417,0.271 2.135,1.938 1.781,1.49 true 1.844,1.354 2.26,1.5 true 1.115,1.667 1.583,1.313 true 1.417,4.083 1.656,3.76 true 0.969,4.063 1.646,3.667 true 2.135,4 1.792,3.656 true 0.24,0.188 0.552,0.385 0.313,0.198 10 false *a 0.24,2.802 0.552,3 0.313,0.198 10 false *b 0.76,1.625 1.188,1.833 0.427,0.208 10 false US1+ 2.188,1.906 2.677,2.146 0.49,0.24 10 false USG1 2.313,1.438 2.729,1.688 0.417,0.25 10 false US1- 0.635,4.021 1.031,4.281 0.396,0.26 10 false UDO- 1.24,4.094 1.74,4.354 0.5,0.26 10 false UJSS 2.167,3.938 2.604,4.198 0.438,0.26 10 false UDO+ 1.594,0.26 2.052,0.458 0.458,0.198 10 false N128 1.615,2.26 2.188,2.573 0.573,0.313 10 false N129
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Disconnect the N128 radio and display receiver assembly connector.


b.

Disconnect the N129 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N128-2 (US1-) - N129-9 (UDO-) Always Below 1 Ω
N128-3 (US1+) - N129-10 (UDO+) Always Below 1 Ω
N128-5 (USG1) - N129-12 (UJSS) Always Below 1 Ω
N128-2 (US1-) or N129-9 (UDO-) - Body ground Always 10 kΩ or higher
N128-3 (US1+) or N129-10 (UDO+) - Body ground Always 10 kΩ or higher
N128-5 (USG1) or N129-12 (UJSS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR