Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › DRIVE BELT
RM35X0E _51 Engine / Hybrid System _079219 1GD-FTV ENGINE MECHANICAL _0385634 DRIVE BELT G

1GD-FTV ENGINE MECHANICAL  DRIVE BELT  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A343690

To prevent injury due to contact with an operating fan and generator V belt or cooling fan, keep your hands and clothing away from the fan and generator V belt and cooling fans when working in the engine compartment with the engine running.


PROCEDURE

Hide 16361A 1.INSPECT FAN AND GENERATOR V BELT

a.
B000543

Check the belt for wear, cracks or other signs of damage.

If any of the following defects is found, replace the fan and generator V belt.

·

The fan and generator V belt is cracked.

·

The fan and generator V belt is worn out to the extent that the cords are exposed.

·

The fan and generator V belt has chunks missing from the ribs.



b.
B000540C05
0.563,0.313 0.729,0.51 0.167,0.198 10 false *a 2.24,0.313 2.406,0.479 0.167,0.167 10 false *b
*a CORRECT
*b INCORRECT


Check that the fan and generator V belt fits properly in the ribbed grooves.

HINT:

Check with your hand to confirm that the fan and generator V belt has not slipped out of the grooves on the bottom of the pulley. If it has slipped out, replace the fan and generator V belt. Install a new fan and generator V belt correctly.



Hide 88359 2.INSPECT VISCOUS HEATER V BELT (w/ Viscous Heater)

a.
B000543

Check the viscous heater V belt for wear, cracks or other signs of damage.

If any of the following defects is found, replace the viscous heater V belt.

·

The viscous heater V belt is cracked.

·

The viscous heater V belt is worn out to the extent that the cords are exposed.

·

The viscous heater V belt has chunks missing from the ribs.



b.
B000540C05
0.563,0.313 0.729,0.51 0.167,0.198 10 false *a 2.24,0.313 2.406,0.479 0.167,0.167 10 false *b
*a CORRECT
*b INCORRECT


Check that the viscous heater V belt fits properly in the ribbed grooves.

HINT:

Check with your hand to confirm that the viscous heater V belt has not slipped out of the grooves on the bottom of the pulley. If it has slipped out, replace the viscous heater V belt. Install a new viscous heater V belt correctly.



c.

Inspect the viscous heater V belt tension or deflection value.

NOTICE:
·

Check and adjust the viscous heater V belt when the engine is cold.

·

Check the viscous heater V belt tension at the specified point.

·

Perform the V belt tension and deflection value check after idling the engine for a few minutes. After this, rotate the crankshaft pulley 2 times and adjust to the middle of the range of values given for "New belt".

·

With the exception of new belts, when reinstalling a belt used for 5 minutes or more, adjust to the middle of the range of values given for "Used belt".



i.
A346689

Using a belt tension gauge, check the viscous heater V belt tension.

Standard Tension:
Item Condition Specified Condition
New belt Crankshaft pulley after 2 rotations 382 to 618 N (39 to 63 kgf, 85.9 to 138.9 lbf)
Used belt Crankshaft pulley after 2 rotations 232 to 428 N (24 to 44 kgf, 52.2 to 96.2 lbf)


If the belt tension is not specified, adjust the viscous heater V belt.


ii.

Check the viscous heater V belt deflection by pressing on the V belt at the point indicated in the illustration with 98 N (10 kgf, 22 lbf) of force.

Standard Drive Deflection:
Item Condition Specified Condition
New belt Crankshaft pulley after 2 rotations 9 to 12 mm (0.354 to 0.472 in.)
Used belt Crankshaft pulley after 2 rotations 11 to 14 mm (0.433 to 0.551 in.)


If the belt tension is not specified, adjust the viscous heater V belt.



Hide 16620 3.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY

a.

Remove the fan and generator V belt.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>DRIVE BELT>REMOVAL


b.
A343931

Check that nothing gets caught in the V-ribbed belt tensioner assembly by turning it clockwise and counterclockwise.

If a malfunction exists, replace the V-ribbed belt tensioner assembly.


c.
A349448C01
2.063,0.344 2.313,0.542 0.25,0.198 10 true *a
*a Turn


Turn the pulley, and check that the tensioner bearing moves smoothly and quietly.

If necessary, replace the tensioner pulley.


d.

Install the fan and generator V belt.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>DRIVE BELT>INSTALLATION