Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL FILTER
RM35X0E _51 Engine / Hybrid System _079306 1GD-FTV FUEL _0385715 FUEL FILTER A

1GD-FTV FUEL  FUEL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

When replacing the fuel filter element assembly, use TOYOTA genuine parts.

·

When replacing the fuel filter element assembly, clean the fuel filter case and remove dirt completely.



PROCEDURE

Hide 23390B 1.REMOVE NO. 2 FUEL FILTER ELEMENT ASSEMBLY

HINT:

To prevent incorrect connections, before disconnecting a fuel hose, make sure to check the color of its paint mark.


a.

w/ Fuel Heater:

i.
A438494C01
0.365,2.156 0.365,1.948 0.365,1.948 0.708,1.427 true 0.948,1.927 0.948,1.719 0.948,1.719 1.156,1.135 true 2.063,0.969 2.375,0.667 2.375,0.667 2.573,0.667 true 1.49,2.083 1.49,1.875 1.49,1.875 1.802,1.156 true 0.063,0.042 0.375,0.198 0.313,0.156 10 true *A 0.26,2.188 0.573,2.344 0.313,0.156 10 true *1 0.823,1.99 1.135,2.146 0.313,0.156 10 true *2 2.583,0.583 2.896,0.74 0.313,0.156 10 true *3 1.406,2.104 1.719,2.26 0.313,0.156 10 true *4
*A w/ Fuel Heater
*1 Fuel Hose (Yellow Paint Mark)
*2 Fuel Hose (Pink Paint Mark)
*3 No. 2 Fuel Hose (White Paint Mark)
*4 No. 3 Fuel Hose (Blue Paint Mark)


Slide the 2 clips and disconnect the No. 2 fuel hose and No. 3 fuel hose from the fuel filter assembly.


ii.

Slide the 2 clips and disconnect the 2 fuel hoses from the fuel filter assembly.


iii.

Detach the clamp and disconnect the connector.


iv.

Remove the bolt from the No. 1 fuel filter protector.



b.

w/o Fuel Heater:

i.
A438493C01
0.74,1.938 0.74,1.729 0.74,1.729 1.083,1.208 true 1.396,1.979 1.396,1.771 1.396,1.771 1.604,1.188 true 0.063,0.042 0.375,0.198 0.313,0.156 10 true *A 0.646,1.958 0.958,2.115 0.313,0.156 10 true *1 1.313,1.99 1.625,2.146 0.313,0.156 10 true *2
*A w/o Fuel Heater
*1 Fuel Hose (Yellow Paint Mark)
*2 Fuel Hose (Pink Paint Mark)


Slide the 2 clips and disconnect the 2 fuel hoses from the fuel filter assembly.


ii.

Detach the clamp and disconnect the connector.


iii.

Remove the bolt from the No. 1 fuel filter protector.



c.
A444464C01
2.167,1.521 2.479,1.677 0.313,0.156 10 true *1 2.948,1.5 3.26,1.656 0.313,0.156 10 true *2
*1 No. 1 Fuel Filter Protector
*2 Fuel Filter Support Stay


Detach the No. 1 fuel filter protector and fuel filter support stay as shown in the illustration.


d.

Remove the fuel filter assembly together with the No. 1 fuel filter protector.


e.
A443473

Connect a hose to the drain cock. Place the other end of the hose into a container under the drain cock.


f.

Loosen the drain cock to drain fuel.


g.

Tighten the drain cock by hand.


h.

Disconnect a hose from the drain cock.


i.
A438496

Slide the fuel filter assembly and lift it up.


j.
A339530

Disconnect the connector.


k.
A438499

Using a screwdriver as a lever, loosen the fastener nut until it can be loosened by hand.


l.
A438500

Fully loosen the fastener nut by hand.


m.
A438501C01
2.146,1.25 2.594,1.25 true 2.625,1.188 2.844,1.385 0.219,0.198 10 false *1
*1 O-ring


To remove the fuel filter cap, pull up one side of the fuel filter cap, and then lift it off.


n.

Remove the No. 2 fuel filter element assembly from the fuel filter case.


o.

Remove the O-ring from the fuel filter case.


Hide 23925 2.REMOVE FUEL FILTER SUPPORT STAY

a.
A443466

Remove the 3 nuts and fuel filter support stay.


Hide 23926 3.REMOVE NO. 2 FUEL FILTER SUPPORT STAY

a.
A443468

Remove the 2 No. 2 fuel filter support stays from the fuel filter support stay.


Hide 23926 4.INSTALL NO. 2 FUEL FILTER SUPPORT STAY

a.

Install the 2 No. 2 fuel filter support stays to the fuel filter support stay.


Hide 23925 5.INSTALL FUEL FILTER SUPPORT STAY

a.

Install the filter support stay with the 3 nuts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 23390B 6.INSTALL NO. 2 FUEL FILTER ELEMENT ASSEMBLY

a.

Clean the fuel filter case and remove dirt completely.


b.
A454665C01
1.635,0.875 2.083,0.688 2.083,0.688 2.25,0.688 true 2.281,0.615 2.479,0.781 0.198,0.167 10 true *1
*1 O-ring


Install a new O-ring to the fuel filter case.


c.

Install the No. 2 fuel filter element assembly to the fuel filter case.


d.
A438502

Align the mark on the fuel filter cap and the mark on the fuel filter case.


e.
A438503N01
2.979,3.792 3.167,3.979 0.188,0.188 10 true A

Push the fuel filter cap onto the fuel filter case by hand.

Standard clearance (A):

1.5 mm (0.0590 in.) or less


HINT:

The clearance between the fuel filter cap and fuel filter case should be even around the entire circumference of the fuel filter cap and fuel filter case.



f.
A439066N01
1.656,4.427 1.802,4.625 0.146,0.198 10 true A 3.229,3.573 3.385,3.729 0.156,0.156 10 true B

Turn the fastener nut until a "click" sound is heard.

HINT:

Just before the marks of the fuel filter case and nut align, the fastener nut will become more difficult to turn. Use a screwdriver as a lever to turn the fastener nut.



g.

Measure the distance between the marks on the fuel filter cap and fuel filter case, and the clearance between the fuel filter cap and fuel filter case.

Standard distance (A):

1.0 mm (0.0393 in.) or more


Standard clearance (B):

1.0 mm (0.0393 in.) or less



h.

Connect the connector.


i.
A438497

Slide the fuel filter assembly to install it.


j.
A438495C01
2.167,1.521 2.479,1.677 0.313,0.156 10 true *1 2.927,1.51 3.24,1.667 0.313,0.156 10 true *2
*1 No. 1 Fuel Filter Protector
*2 Fuel Filter Support Stay


Install the No. 1 fuel filter protector and fuel filter support stay as shown in the illustration.


k.

w/ Fuel Heater:

HINT:

Make sure that the fuel hose paint marks are as shown in the illustration.


i.

Install the bolt to the No. 1 fuel filter protector.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


ii.

Connect the connector and attach the clamp.


iii.

Connect the 2 fuel hoses to the fuel filter assembly and slide the 2 clips to secure the hoses.


iv.

Connect the No. 2 fuel hose and No. 3 fuel hose to the fuel filter assembly and slide the 2 clips to secure the hoses.



l.

w/o Fuel Heater:

HINT:

Make sure that the fuel hose paint marks are as shown in the illustration.


i.

Install the bolt to the No. 1 fuel filter protector.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


ii.

Connect the connector and attach the clamp.


iii.

Connect the 2 fuel hoses to the fuel filter assembly and slide the 2 clips to secure the hoses.



Hide 7.RESET FUEL SYSTEM WARNING LIGHT

a.

Turn the ignition switch to ON.


b.
A438504

After turning the ignition switch to ON, connect the connector no sooner than 3 seconds have passed but no later than 60 seconds have passed.


c.

Check that the combination meter's fuel system warning light turns off.