Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER › 2019.02–2019.06
RM35X0E _59 Vehicle Exterior _079322 EXTERIOR PANELS / TRIM _0385748 REAR BUMPER A

EXTERIOR PANELS / TRIM  REAR BUMPER  DISASSEMBLY  


PROCEDURE

Hide 82182 1.REMOVE NO. 2 LUGGAGE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)

a.

Disconnect the 4 connectors.


b.

Detach the wire harness clamp and remove the No. 2 luggage room wire.

B525657


Hide 89348Y 2.REMOVE REAR ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)

HINT:

When removing the rear ultrasonic sensor clip, if the double-sided tape is difficult to remove, heat the adhesive of the rear ultrasonic sensor clip and rear bumper cover using a heat light.


Standard Value:
Part Temperature
Rear Bumper Cover 20 to 30°C (68 to 86°F)
Rear Ultrasonic Sensor Clip 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat rear ultrasonic sensor clip excessively.


a.

Remove the 7 rear ultrasonic sensor clips.

B525658


Hide 89342 3.REMOVE REAR CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89342A 4.REMOVE REAR CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89348D 5.REMOVE ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)

Hide 89348R 6.REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89348S 7.REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 52016A 8.REMOVE REAR BUMPER ARM SUB-ASSEMBLY LH (w/ Rear Bumper Arm)

a.
B544350

Remove the 2 bolts.


b.

Detach the hook and remove the rear bumper arm sub-assembly LH.


Hide 52015A 9.REMOVE REAR BUMPER ARM SUB-ASSEMBLY RH (w/ Rear Bumper Arm)

HINT:

Use the same procedure for the RH and LH side.


Hide 76626D 10.REMOVE REAR QUARTER PANEL MUDGUARD LH (w/ Mudguard)

Hide 76625D 11.REMOVE REAR QUARTER PANEL MUDGUARD RH (w/ Mudguard)

HINT:

Use the same procedure for the RH and LH side.


Hide 61682A 12.REMOVE REAR WHEEL OPENING EXTENSION LH

a.

w/ Rear Wheel House Liner:

i.
B525648

Remove the 2 screws.


ii.
B525649C01
0,0 0,0 false
V113147

Move in this Direction


Fold back the rear wheel house liner LH in the direction indicated by the arrow shown in the illustration.



b.
B542963

Using a screwdriver, remove the 4 grommets and rear wheel opening extension LH.


Hide 61681C 13.REMOVE REAR WHEEL OPENING EXTENSION RH

HINT:

Use the same procedure for the RH and LH side.


Hide 52156A 14.REMOVE REAR BUMPER SIDE SUPPORT LH

a.
B525651C01
1.927,2.292 2.146,2.479 0.219,0.188 10 true *a
*a 90°
V113147

Move in this Direction


Using a screwdriver, turn the clip 90° and detach the clip as shown in the illustration.


b.
B525652C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Detach the guide and claw and remove the rear bumper side support LH as shown in the illustration.


Hide 52155A 15.REMOVE REAR BUMPER SIDE SUPPORT RH

HINT:

Use the same procedure for the RH and LH side.


Hide 52158C 16.REMOVE REAR BUMPER NO. 2 SIDE SUPPORT LH

a.
B525654C01
0.969,1.063 1.188,1.26 0.219,0.198 10 true *a
*a 90°
V113147

Move in this Direction


Using a screwdriver, turn the clip 90° and detach the clip as shown in the illustration.


b.
B525655C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the guide and claw and remove the rear bumper No. 2 side support LH as shown in the illustration.


Hide 52157A 17.REMOVE REAR BUMPER NO. 2 SIDE SUPPORT RH

HINT:

Use the same procedure for the RH and LH side.