Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2019.02–2019.06
RM35X0E _58 Vehicle Interior _078602 SEAT BELT _0385912 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Rear Seat Belt Warning Light Malfunction  


DESCRIPTION

The combination meter assembly detects the rear seat belt state. The rear seat belt warning light on the telltale light assembly illuminates, blinks or turns off in accordance with the vehicle speed and rear seat belt state.

WIRING DIAGRAM

E416527E02
2.385,6.76 3.719,7.146 1.333,0.385 10 false Rear Seat Inner Belt Assembly RH 2.333,4.979 3.667,5.365 1.333,0.385 10 false Rear Seat Inner Belt Assembly LH 3.854,6.771 5.281,7.146 1.427,0.375 10 false V14 3.833,6.906 5.26,7.281 1.427,0.375 10 false Rear Center Seat Inner Belt Assembly 5.771,6.635 7.052,7.01 1.281,0.375 10 false N23 5.771,6.813 7.052,7.188 1.281,0.375 10 false Combination Meter Assembly 5.927,5.75 6.729,6.031 0.802,0.281 10 false RRSB 5.938,3.969 6.74,4.25 0.802,0.281 10 false RLSB 5.938,2.854 6.74,3.135 0.802,0.281 10 false RCSB 2.469,6.417 3.802,6.802 1.333,0.385 10 false Buckle Switch 2.479,4.656 3.813,5.042 1.333,0.385 10 false Buckle Switch 2.438,3.531 3.771,3.917 1.333,0.385 10 false Buckle Switch 0.375,3.76 2.229,4.083 1.854,0.323 10 false Occupant Detection Sensor 0.365,4.875 2.219,5.198 1.854,0.323 10 false Occupant Detection Sensor 0.354,6.646 2.208,6.969 1.854,0.323 10 false Occupant Detection Sensor 0.5,7.021 2.354,7.344 1.854,0.323 10 false No. 1 Seat Cushion Pad 4.906,2.823 5.521,3.198 0.615,0.375 10 false CBR+ 4.948,3.271 5.563,3.646 0.615,0.375 10 false LBE- 4.927,3.917 5.542,4.292 0.615,0.375 10 false LBR+ 5.385,3.927 6,4.302 0.615,0.375 10 false 1 5.385,3.26 6,3.635 0.615,0.375 10 false 5 5.375,2.802 5.99,3.177 0.615,0.375 10 false 6 5.406,5.677 6.021,6.052 0.615,0.375 10 false 2 4.906,5.688 5.521,6.063 0.615,0.375 10 false RBR+ 5.646,5.677 6.26,6.052 0.615,0.375 10 false 35 5.625,3.938 6.24,4.313 0.615,0.375 10 false 36 5.625,2.813 6.24,3.188 0.615,0.375 10 false 19 2.823,2 4.646,2.385 1.823,0.385 10 false N30 2.833,2.167 4.771,2.552 1.938,0.385 10 false Indicator Assembly (Rear Seat Belt Warning Light) 2.073,1.177 3.406,1.563 1.333,0.385 10 false ECU-IG1 NO.4 0.479,0.927 1.813,1.313 1.333,0.385 10 false from IG1-NO.2 Relay 3.208,0.948 3.708,1.344 0.5,0.396 10 false IG 3.198,1.604 3.698,2 0.5,0.396 10 false E 3.01,1.5 3.51,1.896 0.5,0.396 10 false 3 2.99,0.823 3.49,1.219 0.5,0.396 10 false 1 3.615,0.948 4.115,1.344 0.5,0.396 10 false R2LM 5.948,0.948 6.448,1.344 0.5,0.396 10 false RLMT 3.604,1.302 4.104,1.698 0.5,0.396 10 false R2CM 5.938,1.302 6.438,1.698 0.5,0.396 10 false RCMT 5.938,1.615 6.438,2.01 0.5,0.396 10 false RRMT 3.656,1.646 4.156,2.042 0.5,0.396 10 false R2RI 4.156,1.542 4.656,1.938 0.5,0.396 10 false 11 4.156,1.198 4.656,1.594 0.5,0.396 10 false 10 4.146,0.833 4.646,1.229 0.5,0.396 10 false 9 5.708,0.844 6.208,1.24 0.5,0.396 10 false 9 5.635,1.219 6.135,1.615 0.5,0.396 10 false 25 5.688,1.573 6.188,1.969 0.5,0.396 10 false 8

CAUTION / NOTICE / HINT

NOTICE:
·

The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK REAR SEAT BELT WARNING LIGHT
a.

Check the rear seat belt warning light.


Result:
Result Proceed to
No rear seat belt warning lights illuminate. A
LH side rear seat belt warning light does not illuminate. B
Center side rear seat belt warning light does not illuminate. C
RH side rear seat belt warning light does not illuminate. D



A

2.INSPECT REAR CENTER SEAT INNER BELT ASSEMBLY

B

5.READ VALUE USING GTS

C

12.READ VALUE USING GTS

D

18.READ VALUE USING GTS
2.INSPECT REAR CENTER SEAT INNER BELT ASSEMBLY
a.

Remove the rear center seat inner belt assembly.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY (for Van)>REMOVAL


b.

Inspect the rear center seat inner belt assembly.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY (for Van)>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (REAR CENTER SEAT INNER BELT ASSEMBLY - BODY GROUND)

NG

REPLACE REAR CENTER SEAT INNER BELT ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (REAR CENTER SEAT INNER BELT ASSEMBLY - BODY GROUND)
a.
E416740C02
1.49,0.281 1.938,0.594 0.448,0.313 0.99,1.792 1.146,1.792 1.146,1.792 1.51,1.438 true 0.219,0.188 0.531,0.385 0.313,0.198 10 false *a 1.583,0.354 1.896,0.552 0.313,0.198 10 false V14 0.625,1.646 1.052,1.896 0.427,0.25 10 false LBE-
*a Front view of wire harness connector
(to Rear Center Seat Inner Belt Assembly)


Disconnect the rear center seat inner belt assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V14-5 (LBE-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (INDICATOR ASSEMBLY [REAR SEAT BELT WARNING LIGHT] - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (INDICATOR ASSEMBLY [REAR SEAT BELT WARNING LIGHT] - BATTERY AND BODY GROUND)
a.
E285189C19
1.51,0.135 1.917,0.385 0.406,0.25 1.177,1.042 0.823,0.698 0.823,0.698 0.656,0.698 true 0.854,0.188 1,0.188 1,0.188 1.448,1.031 true 0.073,0.042 0.385,0.198 0.313,0.156 10 false *a 1.625,0.167 2.083,0.365 0.458,0.198 10 false N30 0.448,0.625 0.813,0.833 0.365,0.208 10 false IG 0.708,0.094 1.073,0.302 0.365,0.208 10 false E
*a Front view wire harness connector
(to Indicator Assembly [Rear Seat Belt Warning Light])


Disconnect the indicator assembly (rear seat belt warning light) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N30-1 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N30-3 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Left Seat Buckle / Occupant Detection Warning Switch Rear seat inner belt LH buckle and occupant detection sensor signal OFF or ON OFF: Rear LH seat belt fastened and occupied
ON: Rear LH seat belt not fastened and occupied
-
Body Electrical > Combination Meter > Data List
Tester Display
Rear Left Seat Buckle / Occupant Detection Warning Switch
50003 409 31
OK:

The GTS display changes correctly in response to the rear seat belt condition.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (INDICATOR ASSEMBLY [REAR SEAT BELT WARNING LIGHT] - COMBINATION METER ASSEMBLY)

NG

8.INSPECT REAR SEAT INNER BELT ASSEMBLY LH
6.CHECK HARNESS AND CONNECTOR (INDICATOR ASSEMBLY [REAR SEAT BELT WARNING LIGHT] - COMBINATION METER ASSEMBLY)
a.

Disconnect the N30 indicator assembly (rear seat belt warning light) connector.


b.

Disconnect the N23 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N30-9 (R2LM) - N23-9 (RLMT) Always Below 1 Ω
N30-9 (R2LM) or N23-9 (RLMT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK INDICATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK INDICATOR ASSEMBLY
a.
C406366C18
1.5,0.167 1.885,0.427 0.385,0.26 0.885,1.188 0.594,1.906 0.594,1.906 0.427,1.906 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.573,0.208 1.885,0.365 0.313,0.156 10 false N23 0.031,1.802 0.49,2.094 0.458,0.292 10 false RLMT
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N23-9 (RLMT) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

8.INSPECT REAR SEAT INNER BELT ASSEMBLY LH
a.

Remove the rear seat inner belt assembly LH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY (for Van)>REMOVAL


b.

Inspect the rear seat inner belt assembly LH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY (for Van)>INSPECTION


Result:
Proceed to
OK
NG



OK

9.INSPECT NO. 1 SEAT CUSHION PAD

NG

REPLACE REAR SEAT INNER BELT ASSEMBLY LH

9.INSPECT NO. 1 SEAT CUSHION PAD
a.

Remove the No. 1 seat cushion pad (occupant detection sensor).

Click hereVehicle Interior>SEAT>OCCUPANT DETECTION SENSOR (for Van)>REMOVAL


b.

Inspect the No. 1 seat cushion pad (occupant detection sensor).

Click hereVehicle Interior>SEAT>OCCUPANT DETECTION SENSOR (for Van)>INSPECTION


Result:
Proceed to
OK
NG



OK

10.INSPECT REAR CENTER SEAT INNER BELT ASSEMBLY

NG

10.INSPECT REAR CENTER SEAT INNER BELT ASSEMBLY
a.

Remove the rear center seat inner belt assembly.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY (for Van)>REMOVAL


b.

Inspect the rear center seat inner belt assembly.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY (for Van)>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (REAR CENTER SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPLACE REAR CENTER SEAT INNER BELT ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (REAR CENTER SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the V14 rear center seat inner belt assembly connector.


b.

Disconnect the N23 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V14-1 (LBR+) - N23-36 (RLSB) Always Below 1 Ω
V14-1 (LBR+) or N23-36 (RLSB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Center Seat Buckle / Occupant Detection Warning Switch Rear seat inner belt (for Center) buckle and occupant detection sensor signal OFF or ON OFF: Rear center seat belt fastened and occupied
ON: Rear center seat belt not fastened and occupied
-
Body Electrical > Combination Meter > Data List
Tester Display
Rear Center Seat Buckle / Occupant Detection Warning Switch
50003 409 32
OK:

The GTS display changes correctly in response to the rear seat belt condition.



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (INDICATOR ASSEMBLY [REAR SEAT BELT WARNING LIGHT] - COMBINATION METER ASSEMBLY)

NG

15.INSPECT REAR CENTER SEAT INNER BELT ASSEMBLY
13.CHECK HARNESS AND CONNECTOR (INDICATOR ASSEMBLY [REAR SEAT BELT WARNING LIGHT] - COMBINATION METER ASSEMBLY)
a.

Disconnect the N30 indicator assembly (rear seat belt warning light) connector.


b.

Disconnect the N23 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N30-10 (R2CM) - N23-25 (RCMT) Always Below 1 Ω
N30-10 (R2CM) or N23-25 (RCMT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK INDICATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK INDICATOR ASSEMBLY
a.
C406366C19
1.5,0.167 1.885,0.427 0.385,0.26 0.865,1.396 0.594,1.906 0.594,1.906 0.427,1.906 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.573,0.208 1.885,0.365 0.313,0.156 10 false N23 0.031,1.802 0.49,2.094 0.458,0.292 10 false RCMT
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N23-25 (RCMT) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

15.INSPECT REAR CENTER SEAT INNER BELT ASSEMBLY
a.

Remove the rear center seat inner belt assembly.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY (for Van)>REMOVAL


b.

Inspect the rear center seat inner belt assembly.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY (for Van)>INSPECTION


Result:
Proceed to
OK
NG



OK

16.INSPECT NO. 1 SEAT CUSHION PAD

NG

REPLACE REAR CENTER SEAT INNER BELT ASSEMBLY

16.INSPECT NO. 1 SEAT CUSHION PAD
a.

Remove the No. 1 seat cushion pad (occupant detection sensor).

Click hereVehicle Interior>SEAT>OCCUPANT DETECTION SENSOR (for Van)>REMOVAL


b.

Inspect the No. 1 seat cushion pad (occupant detection sensor).

Click hereVehicle Interior>SEAT>OCCUPANT DETECTION SENSOR (for Van)>INSPECTION


Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (REAR CENTER SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

17.CHECK HARNESS AND CONNECTOR (REAR CENTER SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the V14 rear center seat inner belt assembly connector.


b.

Disconnect the N23 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V14-6 (CBR+) - N23-19 (RCSB) Always Below 1 Ω
V14-6 (CBR+) or N23-19 (RCSB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Right Seat Buckle / Occupant Detection Warning Switch Rear seat inner belt RH buckle and occupant detection sensor signal OFF or ON OFF: Rear RH seat belt fastened and occupied
ON: Rear RH seat belt not fastened and occupied
-
Body Electrical > Combination Meter > Data List
Tester Display
Rear Right Seat Buckle / Occupant Detection Warning Switch
50003 409 30
OK:

The GTS display changes correctly in response to the rear seat belt condition.



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (INDICATOR ASSEMBLY [REAR SEAT BELT WARNING LIGHT] - COMBINATION METER ASSEMBLY)

NG

21.INSPECT REAR SEAT INNER BELT ASSEMBLY RH
19.CHECK HARNESS AND CONNECTOR (INDICATOR ASSEMBLY [REAR SEAT BELT WARNING LIGHT] - COMBINATION METER ASSEMBLY)
a.

Disconnect the N30 indicator assembly (rear seat belt warning light) connector.


b.

Disconnect the N23 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N30-11 (R2RI) - N23-8 (RRMT) Always Below 1 Ω
N30-11 (R2RI) or N23-8 (RRMT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

20.CHECK INDICATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK INDICATOR ASSEMBLY
a.
C406366C17
1.5,0.167 1.885,0.427 0.385,0.26 0.781,1.188 0.594,1.906 0.594,1.906 0.427,1.906 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.573,0.208 1.885,0.365 0.313,0.156 10 false N23 0.031,1.802 0.49,2.094 0.458,0.292 10 false RRMT
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N23-8 (RRMT) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

21.INSPECT REAR SEAT INNER BELT ASSEMBLY RH
a.

Remove the rear seat inner belt assembly RH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY (for Van)>REMOVAL


b.

Inspect the rear seat inner belt assembly RH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY (for Van)>INSPECTION


Result:
Proceed to
OK
NG



OK

22.INSPECT NO. 1 SEAT CUSHION PAD

NG

REPLACE REAR SEAT INNER BELT ASSEMBLY RH

22.INSPECT NO. 1 SEAT CUSHION PAD
a.

Remove the No. 1 seat cushion pad (occupant detection sensor).

Click hereVehicle Interior>SEAT>OCCUPANT DETECTION SENSOR (for Van)>REMOVAL


b.

Inspect the No. 1 seat cushion pad (occupant detection sensor).

Click hereVehicle Interior>SEAT>OCCUPANT DETECTION SENSOR (for Van)>INSPECTION


Result:
Proceed to
OK
NG



OK

23.INSPECT REAR CENTER SEAT INNER BELT ASSEMBLY

NG

23.INSPECT REAR CENTER SEAT INNER BELT ASSEMBLY
a.

Remove the rear center seat inner belt assembly.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY (for Van)>REMOVAL


b.

Inspect the rear center seat inner belt assembly.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY (for Van)>INSPECTION


Result:
Proceed to
OK
NG



OK

24.CHECK HARNESS AND CONNECTOR (REAR CENTER SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPLACE REAR CENTER SEAT INNER BELT ASSEMBLY

24.CHECK HARNESS AND CONNECTOR (REAR CENTER SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the V14 rear center seat inner belt assembly connector.


b.

Disconnect the N23 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V14-2 (RBR+) - N23-35 (RRSB) Always Below 1 Ω
V14-2 (RBR+) or N23-35 (RRSB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR