Use the following procedure to troubleshoot the lighting system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Measure the battery voltage.
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
Check the fuses and relays.
Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
| Proceed to |
|---|
| NEXT |
NEXT
Use the GTS to check if the CAN communication system is functioning normally.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
CAN communication system DTCs are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check for DTCs and note any codes that are output.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Headlight ECU)>DTC CHECK / CLEAR
Body Electrical / Main Body / Trouble Codes.
w/ Automatic High Beam System
Body Electrical / Front Recognition Camera (Front Lighting Control) / Trouble Codes.
Clear the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Headlight ECU)>DTC CHECK / CLEAR
Body Electrical / Main Body / Clear DTCs.
w/ Automatic High Beam System
Body Electrical / Front Recognition Camera (Front Lighting Control) / Clear DTCs.
Recheck for DTCs by simulating the operation indicated by the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Headlight ECU)>DTC CHECK / CLEAR
Body Electrical / Main Body / Trouble Codes.
w/ Automatic High Beam System
Body Electrical / Front Recognition Camera (Front Lighting Control) / Trouble Codes.
| Result | Proceed to |
|---|---|
| Malfunction is duplicated but DTCs are not output (w/ Automatic High Beam System) | A |
| DTCs are output | B |
| Malfunction cannot be duplicated and DTCs are not output (w/ Automatic High Beam System) | C |
| DTCs are not output (w/o Automatic High Beam System) | D |
A
B
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Headlight ECU)>DIAGNOSTIC TROUBLE CODE CHART
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
D
Refer to Vehicle Control History.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Headlight ECU)>VEHICLE CONTROL HISTORY
Check for vehicle control history and note any codes that are output.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| No vehicle control history is output | A |
| X2020 or X204D is output | B |
| Any vehicle control history other than X2020 and X204D is output | C |
A
B
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Headlight ECU)>VEHICLE CONTROL HISTORY
C
Refer to Problem Symptoms Table.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Headlight ECU)>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Refer to Vehicle Control History.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Headlight ECU)>VEHICLE CONTROL HISTORY
Clear the vehicle control history.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Recheck for vehicle control history.
Check if any vehicle control history is output.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| Vehicle control history is not output | A |
| Vehicle control history is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Headlight ECU)>VEHICLE CONTROL HISTORY