The main body ECU (multiplex network body ECU) controls the operation of the TAIL relay.
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Taillight Relay | Taillight relay | OFF or ON | - |
| Tester Display |
|---|
| Taillight Relay |
Taillights illuminate.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Headlight ECU)>PROBLEM SYMPTOMS TABLE
NG
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
Disconnect the instrument panel junction block assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3E-1 - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3G-1 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for LHD | *B | for RHD |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Connect a positive (+) lead from the battery to terminal 3E-1*1 or 3G-1*2.
*1: for LHD
*2: for RHD
Connect a negative (-) lead from the battery to terminal A-14 (TRLY).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3C-32 - Battery negative (-) terminal | Battery voltage is applied between terminals 3E-1 - A-14 (TRLY) | 11 to 14 V |
| 3B-11 - Battery negative (-) terminal | Battery voltage is applied between terminals 3E-1 - A-14 (TRLY) | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3C-32 - Battery negative (-) terminal | Battery voltage is applied between terminals 3G-1 - A-14 (TRLY) | 11 to 14 V |
| 3B-11 - Battery negative (-) terminal | Battery voltage is applied between terminals 3G-1 - A-14 (TRLY) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL