AIR CONDITIONING AMPLIFIER ASSEMBLY
Disconnect the N42 air conditioning amplifier assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No.
(Symbol) |
Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| N42-5 (B) - Body ground | P - Body ground | Power source (Back-up) | Always | 11 to 14 V |
| N42-6 (IG+) - Body ground | P - Body ground | Power source (IG) | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| N42-17 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the N42 air conditioning amplifier assembly connector.
Measure the voltage, resistance and pulse according to the value(s) in the table below.
| Terminal No.
(Symbol) |
Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| N43-3 (SG-1) - Body ground | LG - Body ground | Ground for sensor | Always | Below 1 Ω |
| N43-5 (TR) - Body ground | B - Body ground | Room temperature sensor signal | ·
Ignition switch ON ·
A/C switch: On ·
Cabin temperature: 25°C (77°F) |
1.05 to 1.45 V |
·
Ignition switch ON ·
A/C switch: On ·
Cabin temperature: 40°C (104°F) |
0.64 to 0.87 V | |||
| N43-6 (PRE) - N43-15 (SG-4) | B - GR | Air conditioner pressure sensor signal | ·
Engine running ·
Air conditioning system operating ·
Refrigerant pressure: Normal pressure (below 3025 kPa [30.8 kgf/cm2, 439 psi] and higher than 176 kPa [1.8 kgf/cm2, 26 psi]) |
0.74 to 4.61 V |
·
Engine running ·
Air conditioning system operating ·
Refrigerant pressure: Abnormal pressure (less than 176 kPa (1.8 kgf/cm2, 26 psi)) |
Below 0.74 V | |||
·
Engine running ·
Air conditioning system operating ·
Refrigerant pressure: Abnormal pressure (more than 3025 kPa (30.8 kgf/cm2, 439 psi)) |
4.61 V or higher | |||
| N43-11 (S5-3) - Body ground | L - Body ground | Power source of sensor | Ignition switch off → ON | Below 1 V → 4.75 to 5.25 V |
| N43-12 (LOCK) - Body ground | B - Body ground | Air conditioning lock sensor signal | ·
Engine running ·
Blower switch: LO ·
A/C switch: On |
Pulse generation
(See waveform 4) |
| N43-14 (SG-5) - Body ground | W - Body ground | Ground for sensor | Always | Below 1 Ω |
| N43-15 (SG-4) - Body ground | GR - Body ground | Ground for sensor | Always | Below 1 Ω |
| N43-16 (PTC2) - Body ground*1 | V - Body ground | Quick heater assembly operation signal | ·
Ignition switch ON ·
Temperature setting: MAX HOT ·
A/C switch: On ·
Ambient temperature: 0°C (32°F) or lower ·
Engine coolant temperature: 62.5°C (144.5°F) or lower ·
Blower switch: Off → LO (after 20 seconds) |
11 to 14 V → Below 1 V |
| N43-17 (PTC3) - Body ground*1 | L - Body ground | Quick heater assembly operation signal | ·
Ignition switch ON ·
Temperature setting: MAX HOT ·
A/C switch: On ·
Ambient temperature: 0°C (32°F) or lower ·
Engine coolant temperature: 62.5°C (144.5°F) or lower ·
Blower switch: Off → LO (after 30 seconds) |
11 to 14 V → Below 1 V |
| N43-19 (MGC) - Body ground | G - Body ground | Magnetic clutch operation signal | ·
Engine running ·
Blower switch: LO ·
A/C switch: Off or on (magnet clutch off) |
11 to 14 V |
·
Engine running ·
Blower switch: LO ·
A/C switch: On (magnet clutch on) |
Below 1 V | |||
| N43-21 (MGCA) - Body ground*2 | P - Body ground | Viscous heater with magnetic clutch assembly operation signal | ·
Engine running ·
Blwoer switch: LO ·
A/C switch: On ·
Heater switch assembly: Off or on (magnet clutch off) |
11 to 14 V |
·
Engine running ·
Blwoer switch: LO ·
A/C switch: On ·
Heater switch assembly: On (magnet clutch on) |
Below 1 V | |||
| N42-1 (CANL) | - | CAN communication line | - | - |
| N42-2 (CANH) | - | CAN communication line | - | - |
| N42-7 (LIN1) - Body ground | V - Body ground | LIN communication signal | Ignition switch ON | Pulse generation
(See waveform 1) |
| N42-12 (SWVC) - Body ground*2, *3 | R - Body ground*2
L - Body ground*3 |
Heater switch assembly operation signal*2
Idle up switch operation signal*3 |
·
Engine running ·
Blower switch: LO ·
A/C switch: On ·
Heater switch assembly: Off → on*2 ·
Idle up switch: Off → on*3 |
11 to 14 V → Below 1 V |
| N42-21 (BLW) - Body ground | Y - Body ground | Blower motor speed control signal | ·
Ignition switch ON ·
Blower switch: LO |
Pulse generation
(See waveform 2) |
| N42-23 (PTC1) - Body ground*1 | W - Body ground | Quick heater assembly operation signal | ·
Ignition switch ON ·
Temperature setting: MAX HOT ·
A/C switch: On ·
Ambient temperature: 0°C (32°F) or lower ·
Engine coolant temperature: 62.5°C (144.5°F) or lower ·
Blower switch: Off → LO (after 10 seconds) |
11 to 14 V → Below 1 V |
| t2-2 (BUSG) - Body ground | - | Ground for BUS IC | Always | Below 1 Ω |
| t2-3 (BUS) - t2-2 (BUSG) | - | BUS IC control signal | Ignition switch ON | Pulse generation
(See waveform 3) |
| t2-4 (BUSB) - t2-2 (BUSG) | - | Power supply for BUS IC | Always | 11 to 14 V |
| t2-5 (SG-3) - Body ground | - | Ground for sensor | Always | Below 1 Ω |
| t2-6 (TE) - t2-5 (SG-3) | - | No. 1 cooler thermistor signal | ·
Ignition switch ON ·
A/C switch: On ·
Evaporator temperature: 0°C (32°F) |
1.7 to 2.1 V |
·
Ignition switch ON ·
A/C switch: On ·
Evaporator temperature: 15°C (59°F) |
0.9 to 1.3 V |
*1: w/ PTC Heater
*2: w/ Viscous Heater
*3: w/ Idle Up Switch
Waveform 1:
| Item | Content |
|---|---|
| Terminal No. | N42-7 (LIN1) - Body ground |
| Tool Setting | 2 V/DIV., 20 μs./DIV. |
| Vehicle Condition | Ignition switch ON |
Waveform 2:
| Item | Content |
|---|---|
| Terminal No. | N42-21 (BLW) - Body ground |
| Tool Setting | 1 V/DIV., 500 μs./DIV. |
| Vehicle Condition | ·
Ignition switch ON ·
Blower switch: LO |
Waveform 3:
| Item | Content |
|---|---|
| Terminal No. | t2-3 (BUS) - t2-2 (BUSG) |
| Tool Setting | 2 V/DIV., 20 μs./DIV. |
| Vehicle Condition | Ignition switch ON |
Waveform 4:
| Item | Content |
|---|---|
| Terminal No. | N43-12 (LOCK) - Body ground |
| Tool Setting | 200 mV/DIV., 10 ms./DIV. |
| Condition | ·
Engine running ·
Blower switch: LO ·
A/C switch: On |
AIR CONDITIONING CONTROL ASSEMBLY
Disconnect the N55 air conditioning control assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No.
(Symbol) |
Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| N55-13 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| N55-9 (IG+) - Body ground | GR - Body ground | Power source (IG) | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
Reconnect the N55 air conditioning control assembly connector.
Check for waveform according to the value(s) in the table below.
| Terminal No.
(Symbol) |
Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| N55-7 (LIN1) - Body ground | V - Body ground | LIN communication | Ignition switch ON | Pulse generation
(See waveform 1) |
Waveform 1:
| Item | Content |
|---|---|
| Terminal No. | N55-7 (LIN1) - Body ground |
| Tool Setting | 2 V/DIV., 20 μs./DIV. |
| Vehicle Condition | Ignition switch ON |
ECM
for 1GD-FTV (w/ DPF):Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>TERMINALS OF ECM
for 1GD-FTV (w/ Urea SCR System):Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>TERMINALS OF ECM
for 1GD-FTV (w/ EGR Cooler):Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>TERMINALS OF ECM
for 1GD-FTV (w/o EGR Cooler):Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>TERMINALS OF ECM
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Headlight ECU)>TERMINALS OF ECU
COMBINATION METER ASSEMBLY
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU