Home › Drivetrain › RC60J (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION SYSTEM (for 1GD-FTV)
RM35X0E _52 Drivetrain _078740 RC60J MANUAL TRANSMISSION / TRANSAXLE _0383350 MANUAL TRANSMISSION SYSTEM(for 1GD-FTV) U

RC60J MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION SYSTEM(for 1GD-FTV)  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and Transmission / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed -
Engine Speed Engine speed Min.: 0 rpm
Max.: 16383 rpm
650 to 750 rpm: Idling with warm engine When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
Mass Air Flow Sensor Airflow rate from mass air flow meter sub-assembly Min.: 0 gm/sec
Max.: 655.35 gm/sec
Idling:
·

3 to 15 gm/sec (EGR on)

·

10 to 21 gm/sec (EGR off)


This is the intake air amount measured by the mass air flow meter sub-assembly.
Intake Manifold Absolute Pressure Absolute pressure inside intake manifold Min.: 0 kPa (0 psi)
Max.: 2047.96 kPa (296.95 psi)
Idling:
·

96 to 105 kPa (EGR on)

·

97 to 107 kPa (EGR off)


·

When the ignition switch is ON or the vehicle is idling, the intake manifold absolute pressure and atmospheric pressure are approximately the same (standard atmospheric pressure = 101 kPa).

Above approximately 1500 rpm, the turbo becomes effective and the pressure becomes higher than atmospheric pressure.

·

Inspect while comparing with "Target Boost Pressure".

·

With the accelerator fully open, if the actual manifold absolute pressure (MAP) is low compared to the target booster pressure by at least 20 kPa for 5 seconds or more, a feeling of insufficient power will occur.

·

When a judgment is difficult, turn off the EGR system and confirm this value.


Intake Manifold Absolute Pressure Supported Status of intake manifold absolute pressure Unsupp or Supp -
·

Supp: The item is supported by the vehicle.

·

Unsupp: The monitor is not supported by the vehicle.


Coolant Temperature Engine coolant temperature Min.: -40°C (-40°F)
Max.: 140°C (284°F)
70 to 90°C (158 to 194°F): After warming up engine
·

If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.

·

After a long soak, the coolant temperature, intake air temperature and ambient temperature are approximately equal.


Actual Throttle Position Bank 1 Actual throttle position Min.: 0%
Max.: 100%
Idling after engine warmed-up: 45 to 100% Closing percentage of the throttle valve.
·

Fully closed: 0%.

·

Fully open: 100%.

HINT:

There is no connection with the accelerator. However, under full load, the throttle is usually fully open (100%).



Symptoms when out of range:
·

Stuck closed: Engine stall, difficult to start, lack of power, black smoke, rough idle

·

Stuck open: Loud turbocharging sound, bad vibration when engine is stopped

·

When ECM detects a malfunction of the diesel throttle (MIL on), engine power is restricted so that the vehicle can drive with a maximum speed of 80 to 100 km/h.


Target Throttle Position Bank 1 Target throttle position Min.: 0%
Max.: 100%
·

Throttle valve fully closed: 0%

·

Throttle valve fully opened: 100%


If there is a malfunction of the throttle actuator, compare the target and actual throttle position values for troubleshooting.
Actual Throttle Position Bank 1 Supported Actual throttle position support Unsupp or Supp -
·

Supp: The item is supported by the vehicle.

·

Unsupp: The monitor is not supported by the vehicle.


Actual Throttle Position Bank 2 Supported Actual No. 2 throttle position support Unsupp or Supp -
·

Supp: The item is supported by the vehicle.

·

Unsupp: The monitor is not supported by the vehicle.


Target Throttle Position Bank 1 Supported Target throttle position support Unsupp or Supp -
·

Supp: The item is supported by the vehicle.

·

Unsupp: The monitor is not supported by the vehicle.


Target Throttle Position Bank 2 Supported Target throttle position (No. 2) support Unsupp or Supp -
·

Supp: The item is supported by the vehicle.

·

Unsupp: The monitor is not supported by the vehicle.


Starter SW Starter signal ON or OFF
·

ON: Starter operating

·

OFF: Starter not operating


-
Stop Light SW Stop light switch status ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
NIM Sensor Speed Input shaft speed (NIM) Min.: 0 rpm
Max.: 16383 rpm
Input shaft speed (NIM) equal to engine speed (NE): Clutch pedal not depressed, vehicle running -
NIM Sensor Voltage Input shaft speed sensor (NIM) output voltage Min.: 0.000 V
Max.: 4.999 V
0.1 to 1.9 V: Clutch pedal not depressed, engine idling -
Shift SW Status (R Range) Back-up light switch status ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Clutch Stroke Position Clutch pedal stroke calculated by ECM Min.: -200%
Max.: 199.9%
Value increases: Clutch pedal released → clutch pedal fully depressed -
Clutch Stroke Sensor Voltage Clutch pedal stroke sensor assembly output voltage Min.: 0.000 V
Max.: 4.999 V
Value increases: Clutch pedal released → clutch pedal fully depressed -
iMT SW iMT switch status ON or OFF
·

ON: iMT switch being pressed and held

·

OFF: iMT switch not pressed


-
iMT Telltale iMT telltale display request OFF, Green or Yellow
·

OFF: iMT system off

·

Green: iMT system stand-by

·

Yellow: iMT system malfunction, indicator light initial check


-
iMT Type iMT installation information Type A or Type B Type B: Installation judgment finished
·

Type B: w/ iMT switch

·

Type A: w/o iMT switch