Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for ERA-GLONASS) › 2019.02–2019.06
RM35X0E _56 Audio / Visual / Telematics _078380 TELEMATICS _0385046 TELEMATICS SYSTEM(for ERA-GLONASS) C

TELEMATICS  TELEMATICS SYSTEM(for ERA-GLONASS)  B15C5  Emergency Switch Error (Open or Short)  


DESCRIPTION

This DTC is stored when the telephone transceiver assembly detects an open or short circuit in the manual (SOS) switch.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C5 Emergency Switch Error (Open or Short) Open or short circuit in the manual (SOS) switch is detected.
·

Telephone transceiver assembly

·

Map light assembly (manual (SOS) switch)

·

Harness or connector



WIRING DIAGRAM

E353339E16
1.042,2.177 2.51,2.417 1.469,0.24 10 false Map Light Assembly 1.052,2.01 1.365,2.208 0.313,0.198 10 false a19 1.51,1.615 2.979,1.833 1.469,0.219 10 false Manual (SOS) Switch 3.406,1.083 3.854,1.271 0.448,0.188 10 false GND3 3.438,0.542 3.823,0.729 0.385,0.188 10 false SIG1 3.875,0.542 4.26,0.729 0.385,0.188 10 false 22 3.885,1.083 4.271,1.271 0.385,0.188 10 false 21 5.167,0.625 5.552,0.813 0.385,0.188 10 false SIG1 5.177,1.094 5.563,1.281 0.385,0.188 10 false SIG- 4.896,1.094 5.281,1.281 0.385,0.188 10 false 26 4.885,0.542 5.271,0.729 0.385,0.188 10 false 27 5.052,1.938 6.458,2.313 1.406,0.375 10 false Telephone Transceiver Assembly 5.031,1.76 5.396,1.969 0.365,0.208 10 false N74

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>REGISTRATION

·

When replacing the telephone transceiver assembly make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)
2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)
a.

Remove the map light assembly (manual (SOS) switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E409659C03
0.667,1.823 1.031,1.219 true 1.427,1.802 1.156,1.24 true 0.115,0.094 0.385,0.313 0.271,0.219 10 false *a 1.323,1.833 1.833,2.115 0.51,0.281 10 false GND3 0.542,1.823 0.958,2.031 0.417,0.208 10 false SIG1
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
22 (SIG1) - 21 (GND3) Manual (SOS) switch not pressed 392 to 432 Ω
22 (SIG1) - 21 (GND3) Manual (SOS) switch pressed 78 to 86 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))

NG

REPLACE MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))
a.

Disconnect the N74 telephone transceiver assembly connector.


b.

Disconnect the a19 map light assembly (manual (SOS) switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N74-27 (SIG1) - a19-22 (SIG1) Always Below 1 Ω
N74-26 (SIG-) - a19-21 (GND3) Always Below 1 Ω
N74-27 (SIG1) or a19-22 (SIG1) - Body ground Always 10 kΩ or higher
N74-26 (SIG-) or a19-21 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for LHD)>REMOVAL


Result:
Proceed to
NEXT



NEXT