Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ENGINE COOLANT TEMPERATURE SENSOR
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0387395 ENGINE COOLANT TEMPERATURE SENSOR G

1GD-FTV ENGINE CONTROL  ENGINE COOLANT TEMPERATURE SENSOR  INSPECTION  


PROCEDURE

Hide 89422C 1.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

a.

Partially immerse the engine coolant temperature sensor in water and warm up the water.


b.

Measure the resistance according to the value(s) in the table below.

A224572C01
5.354,0.979 5.99,0.979 true 1.24,0.146 1.552,0.302 0.313,0.156 10 false *a 4.354,0.052 4.667,0.208 0.313,0.156 10 false *b 4.438,2.333 4.75,2.49 0.313,0.156 10 false *c 6.031,0.875 6.344,1.031 0.313,0.156 10 false *d 4.625,0.125 4.938,0.323 0.313,0.198 10 false 30 4.625,0.271 4.938,0.469 0.313,0.198 10 false 20 4.625,0.479 4.938,0.677 0.313,0.198 10 false 10 4.698,0.719 4.865,0.896 0.167,0.177 10 false 5 4.698,0.875 4.865,1.052 0.167,0.177 10 false 3 4.698,1.01 4.865,1.188 0.167,0.177 10 false 2 4.688,1.219 4.854,1.396 0.167,0.177 10 false 1 4.583,1.469 4.885,1.646 0.302,0.177 10 false 0.5 4.583,1.635 4.885,1.813 0.302,0.177 10 false 0.3 4.583,1.771 4.885,1.948 0.302,0.177 10 false 0.2 4.583,1.99 4.885,2.167 0.302,0.177 10 false 0.1 4.802,2.292 5.063,2.479 0.26,0.188 10 false -20 5.135,2.292 5.292,2.49 0.156,0.198 10 false 0 5.344,2.292 5.573,2.49 0.229,0.198 10 false 20 5.583,2.292 5.823,2.479 0.24,0.188 10 false 40 5.833,2.292 6.073,2.479 0.24,0.188 10 false 60 6.073,2.292 6.313,2.479 0.24,0.188 10 false 80 6.281,2.292 6.521,2.479 0.24,0.188 10 false 100 4.74,2.427 5.052,2.604 0.313,0.177 10 false (-4) 4.958,2.427 5.302,2.615 0.344,0.188 10 false (32) 5.198,2.427 5.542,2.615 0.344,0.188 10 false (68) 5.438,2.427 5.844,2.604 0.406,0.177 10 false (104) 5.75,2.427 6.156,2.604 0.406,0.177 10 false (140) 6.063,2.427 6.469,2.604 0.406,0.177 10 false (176) 6.375,2.427 6.781,2.604 0.406,0.177 10 false (212) 4.333,0.365 4.646,0.563 0.313,0.198 10 false kΩ 6.635,2.281 7.104,2.469 0.469,0.188 10 false °C (°F)
*a Component without harness connected
(Engine Coolant Temperature Sensor)
*b Resistance
*c Temperature *d Acceptable Range


Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 2.32 to 2.59 kΩ
80°C (176°F) 0.310 to 0.326 kΩ


CAUTION:
·

Do not put your hands in the water warmed up during the inspection.

·

Touching the hot water may result in burns.



NOTICE:

When checking the engine coolant temperature sensor in water, do not allow water to contact the terminals. After completing the check, dry the engine coolant temperature sensor.


If the result is not as specified, replace the engine coolant temperature sensor.