Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › RELAY
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0387403 RELAY G

1GD-FTV ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 82641 1.INSPECT NO. 1 INTEGRATION RELAY

A443588C05
1.438,2 1.75,2.198 0.313,0.198 2.438,1.99 2.75,2.188 0.313,0.198 3.531,1.99 3.844,2.188 0.313,0.198 4.563,1.979 4.875,2.177 0.313,0.198 5.51,1.99 5.823,2.188 0.313,0.198 0.094,0.094 0.469,0.406 0.375,0.313 10 false *a 1.51,2.01 1.813,2.25 0.302,0.24 10 false 1B 2.51,2 2.813,2.24 0.302,0.24 10 false 1C 3.604,2 3.906,2.24 0.302,0.24 10 false 1D 4.615,1.99 4.917,2.229 0.302,0.24 10 false 1E 5.563,2 5.802,2.167 0.24,0.167 10 false 1H
*a Component without harness connected
(No. 1 Integration Relay)
- -


NOTICE:
·

The IG2 MAIN relay, EDU relay, NOX relay and E/G W/PMP relay are built into the No. 1 integration relay.

·

Before performing the relay inspections for the relays of the No. 1 integration relay, inspect the IG2-MAIN, NOX and E/G W/PMP fuses.



a.

Inspect the IG2 MAIN relay.

i.

Inspect the IG2-MAIN fuse.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1D-1 - 1H-1 Battery voltage not applied to terminals 1D-2 and 1E-4 10 kΩ or higher
Battery voltage applied to terminals 1D-2 and 1E-4 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.



b.

Inspect the EDU relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-1 - 1B-3 Battery voltage not applied to terminals 1B-6 and 1C-4 10 kΩ or higher
Battery voltage applied to terminals 1B-6 and 1C-4 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.



c.

Inspect the NOX relay.

i.

Inspect the NOX fuse.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-3 - 1H-1 Battery voltage not applied to terminals 1E-1 and 1E-4 10 kΩ or higher
Battery voltage applied to terminals 1E-1 and 1E-4 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.



d.

Inspect the E/G W/PMP relay.

i.

Inspect the E/G W/PMP fuse.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-10 - 1H-1 Battery voltage not applied to terminals 1E-4 and 1E-8 10 kΩ or higher
Battery voltage applied to terminals 1E-4 and 1E-8 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.



Hide 89561F 2.INSPECT EFI MAIN RELAY

a.
A301376N10
2.344,0.771 2.656,0.469 2.656,0.469 2.719,0.469 false 2.313,1.458 2.063,1.75 2.063,1.75 1.979,1.75 false 1.917,1.115 1.656,1.115 false 2.688,1.104 3.021,1.104 false 0.292,1.313 0.438,1.49 0.146,0.177 10 false 1 1.271,1.302 1.417,1.479 0.146,0.177 10 false 2 0.302,0.781 0.448,0.958 0.146,0.177 10 false 3 1.281,0.781 1.427,0.958 0.146,0.177 10 false 5 2.76,0.396 2.906,0.573 0.146,0.177 10 false 1 1.875,1.667 2.021,1.844 0.146,0.177 10 false 2 1.49,1 1.635,1.177 0.146,0.177 10 false 3 3.073,1.021 3.219,1.198 0.146,0.177 10 false 5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the EFI MAIN relay.


Hide 896B1A 3.INSPECT DCU MAIN RELAY (w/ Urea SCR System)

a.
A301376N10
2.344,0.771 2.656,0.469 2.656,0.469 2.719,0.469 false 2.313,1.458 2.063,1.75 2.063,1.75 1.979,1.75 false 1.917,1.115 1.656,1.115 false 2.688,1.104 3.021,1.104 false 0.292,1.313 0.438,1.49 0.146,0.177 10 false 1 1.271,1.302 1.417,1.479 0.146,0.177 10 false 2 0.302,0.781 0.448,0.958 0.146,0.177 10 false 3 1.281,0.781 1.427,0.958 0.146,0.177 10 false 5 2.76,0.396 2.906,0.573 0.146,0.177 10 false 1 1.875,1.667 2.021,1.844 0.146,0.177 10 false 2 1.49,1 1.635,1.177 0.146,0.177 10 false 3 3.073,1.021 3.219,1.198 0.146,0.177 10 false 5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the DCU MAIN relay.