CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | for LHD | *B | for RHD |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Connect the instrument panel junction block assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: w/o Stop and Start System *2: w/ Stop and Start System |
||||
| A-32 (IG) - Body ground | None - Body ground | Ignition power supply | Ignition switch ON | 11 to 14 V*1
10.5 to 16 V*2 |
| Ignition switch off | Below 1 V | |||
| A-31 (BECU) - Body ground | None - Body ground | Battery power supply | Always | 11 to 14 V |
| A-30 (ACC) - Body ground | None - Body ground | ACC power supply | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| A-11 (GND1) - Body ground | None - Body ground | Ground | Always | Below 1 Ω |
Install the main body ECU (multiplex network body ECU).
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3B-17 - Body ground | G - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
| *A | for LHD |
| *B | for RHD |
Disconnect the R11*1 or R1*2 multiplex network master switch assembly connector.
*1: for LHD
*2: for RHD
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R11-1 (B) - Body ground | P - Body ground | Battery power supply | Always | 11 to 14 V |
| R11-6 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R1-1 (B) - Body ground | P - Body ground | Battery power supply | Always | 11 to 14 V |
| R1-6 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R11-5 (LIN1) - Body ground | GR - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R1-5 (LIN1) - Body ground | W - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
| *A | for LHD |
| *B | for RHD |
Disconnect the R12*1 or R17*2 power window regulator motor assembly LH connector.
*1: for LHD
*2: for RHD
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R12-2 (B) - Body ground | L - Body ground | Battery power supply | Always | 11 to 14 V |
| R12-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R17-2 (B) - Body ground | R - Body ground | Battery power supply | Always | 11 to 14 V |
| R17-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R12-9 (LIN) - Body ground | P - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R17-9 (LIN) - Body ground | G - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
| *A | for LHD |
| *B | for RHD |
Disconnect the R7*1 or R2*2 power window regulator motor assembly RH connector.
*1: for LHD
*2: for RHD
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R7-2 (B) - Body ground | R - Body ground | Battery power supply | Always | 11 to 14 V |
| R7-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R2-2 (B) - Body ground | L - Body ground | Battery power supply | Always | 11 to 14 V |
| R2-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R7-9 (LIN) - Body ground | G - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R2-9 (LIN) - Body ground | P - Body ground | LIN communication line | Ignition switch ON | Pulse generation |