Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2019.02–2019.06
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0385516 ECD SYSTEM(w/ DPF) L

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  PRECAUTION  


INITIALIZATION AND REGISTRATION


NOTICE:

When replacing the ECM and/or any other components in the following chart, perform the corresponding utility items.


HINT:

When the ECM and one or more other components are replaced at the same time, perform the following utility items by following the instructions shown on the GTS display, starting with the ECM.

Replacement Part Utility Item
ECM
·

Learning Values Save

(Click here)

·

Learning Values Write

(Click here)

·

VIN Registration

(Click here)


Engine assembly
·

Clear Crank Time Compensation Learning Value Data

Click here(Click here)

·

Input Injector Compensation Code

(Click here)

·

Pilot Quantity Learning

(Click here)


Crankshaft angle sensor plate Clear Crank Time Compensation Learning Value Data
Click here(Click here)
Air fuel ratio sensor Clear A/F Sensor Learning Value data
Click here(Click here)
Exhaust manifold converter sub-assembly Clear DPF Thermal Deterioration Data
Click here(Click here)
Injector assembly
·

Input Injector Compensation Code

(Click here)

·

Pilot Quantity Learning

(Click here)


Diesel throttle body assembly Initialization
Click here(Click here)
Electric EGR control valve assembly
Turbocharger sub-assembly or turbocharger nozzle vane control actuator


HINT:

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initializations/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.



CATALYST RECORD OF DPF THERMAL DETERIORATION


HINT:

The ECM stores the history data of DPF catalyst thermal deterioration. This data is updated continuously and then converted to an 8-digit code and stored in the EEPROM. If the ECM determines that replacement of the exhaust manifold converter sub-assembly is required based on the thermal deterioration data, a DTC is stored to inform the driver.


a.

When only the exhaust manifold converter sub-assembly is replaced.

i.

After replacing the exhaust manifold converter sub-assembly, clear the thermal deterioration data stored in the ECM.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION



b.

When only the ECM is replaced.

i.

After replacing the ECM, input the original thermal deterioration data stored before replacement.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION

HINT:
·

Read the thermal deterioration data stored in the ECM before replacement, and store the data in the GTS.

·

If the thermal deterioration data cannot be read, be sure to replace the exhaust manifold converter sub-assembly with a new one and initialize the ECM.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION






INJECTOR COMPENSATION CODE


HINT:
·

Each injector assembly has different fuel injection characteristics. In order to optimize fuel injection performance, the ECM compensates for these differences by adjusting the fuel injection duration of each injector assembly according to its compensation code. Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly.

·

If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.



a.
A340465C01
1.094,0.865 0.948,0.49 0.948,0.49 0.813,0.49 false 0.083,0.083 0.302,0.271 0.219,0.188 10 false *a 0.625,0.427 0.938,0.625 0.313,0.198 10 false *b
*a Example
*b Injector Compensation Code


When an injector assembly is replaced, the injector compensation code must be input into the ECM.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION


b.

When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION



PILOT QUANTITY LEARNING


HINT:
·

By performing "Pilot Quantity Learning", the injection volume for each cylinder is precisely adjusted so that the engine runs smoothly. The "Pilot Quantity Learning" information is stored in the EEPROM of the ECM.

·

If an incorrect pilot quantity learning value is input into the ECM, the engine may rattle or engine idling may become rough.



a.

When an injector assembly is replaced, the injector compensation code must be input to the ECM, and then pilot quantity learning must be performed.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION


b.

When the ECM is replaced, all of the existing injector pilot quantity learning values must be input into the new ECM.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION



WHEN USING GTS


CAUTION:

Observe the following items for safety reasons:

-

Before using the GTS, read the instruction manual.

-

Prevent the GTS cable from being caught on the pedals, shift lever or steering wheel when driving with the GTS connected to the vehicle.

-

When driving the vehicle for testing purposes using the GTS, 2 persons are required. One drives the vehicle, and the other operates the GTS.