Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP (for 1GD-FTV(w/ Variable Flow Control Solenoid Valve))
RM35X0E _55 Steering _078944 POWER ASSIST SYSTEMS _0388797 VANE PUMP(for 1GD-FTV(w/ Variable Flow Control Solenoid Valve)) A

POWER ASSIST SYSTEMS  VANE PUMP(for 1GD-FTV(w/ Variable Flow Control Solenoid Valve))  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 1.INSTALL VANE PUMP SIDE PLATE

a.
C322713C01
0,0 0,0 false
V100135

Power Steering Fluid


Coat a new O-ring with power steering fluid and install it to the front housing.


b.
C412765C01
0,0 0,0 false
V100135

Power Steering Fluid
V113147

Install in this Direction


Coat a new O-ring with power steering fluid and install it to the front vane pump side plate.


c.
C412766C01
0,0 0,0 false
V113147

Install in this Direction


Install the front vane pump side plate to the front housing while aligning the semicircle-shaped cuts of both parts.

NOTICE:

Be sure to install the front vane pump side plate in the correct position and with the correct orientation.



Hide 2.INSTALL VANE PUMP CAM RING

a.
C412767C01
0.854,0.427 0.75,0.25 0.75,0.25 0.625,0.25 true 0.417,0.167 0.729,0.365 0.313,0.198 10 false *a
*a Inscribed Mark
V113147

Install in this Direction


With the inscribed mark facing upward, install the vane pump cam ring to the front housing while aligning the semicircle-shaped cuts of both parts.

NOTICE:

Be sure to install the vane pump cam ring in the correct position and with the correct orientation.



Hide 3.INSTALL VANE PUMP ROTOR

a.
C412768C01
0,0 0,0 false
V113147

Install in this Direction


Install the vane pump rotor with the inscribed mark facing outward.

HINT:

The top and bottom of the vane pump rotor are symmetrical.



b.

Coat the 10 vane pump plates with power steering fluid.


c.
C324329C01
0.552,0.604 0.865,0.76 0.313,0.156 10 false *a 1.646,0.073 1.958,0.229 0.313,0.156 10 false *b
*a Outward
*b Inward


Install the 10 vane pump plates.

NOTICE:

Make sure that the round ends of the vane pump plates are facing outward.



Hide 4.INSTALL VANE PUMP SHAFT SNAP RING

a.
C412769

Using a screwdriver and snap ring expander, install a new vane pump shaft snap ring to the shaft with pulley.


Hide 5.INSTALL REAR HOUSING

a.

Coat the vane pump rear housing of the shaft sub-assembly with pulley and the surrounding surface with power steering fluid.


b.

Coat a new O-ring with power steering fluid and install it to the rear housing.


c.
C412770C01
1.469,1.479 0.656,1.469 0.656,1.469 1.073,1.094 false 0.448,1.385 0.76,1.583 0.313,0.198 10 false *a
*a Align


Align the straight pin of the rear housing with the hole created by the semicircle-shaped cuts of the vane pump cam ring, front vane pump side plate and front housing.

NOTICE:

Make sure that the O-ring is not out of position before installing the rear housing.



d.

Install the rear housing with the 4 bolts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 6.INSPECT ROTATING TORQUE

a.

Check that the vane pump assembly rotates smoothly without abnormal noise.


b.
C412771C01
0.563,0.75 1.208,1.198 true 0.375,0.635 0.688,0.833 0.313,0.198 10 false *a
*a Service Bolt


Temporarily install the service bolt.

Recommended Service Bolt:
Item Specified Condition
Thread Diameter 10 mm (0.394 in.)
Thread Pitch 1.25 mm (0.0492 in.)
Bolt Length 50 mm (1.97 in.)



c.

Using a torque wrench, check the pump rotating torque.

Standard rotating torque:

0.27 N*m (3 kgf*cm, 2 in.*lbf) or less


If the rotating torque is not as specified, check the assembling state of the vane pump assembly.


Hide 44337 7.INSTALL POWER STEERING SUCTION PORT UNION

a.

Coat a new O-ring of the suction port union with power steering fluid.


b.

Install the power steering suction port union to the vane pump assembly.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)