The blower motor assembly reads the signal and controls operation and speed changes of the blower motor.
If the blower air volume is weak, or there are any other blower malfunctions such as the temperature or air volume cannot be changed, the following causes are possible.
| Malfunction Status | Factor |
|---|---|
·
No heating at all. (Airflow volume control is normal.) ·
Air outlet temperature does not increase. (Airflow volume control is normal.) ·
Blower airflow volume is weak. ·
Blower airflow volume cannot be changed. |
Rear blower motor circuit malfunction |
Inspect the fuses for circuits related to this system before performing the following procedure.
Remove the heater relay (HTR RR NO.1) from the No. 1 engine room relay block assembly.
Inspect the heater relay (HTR RR NO.1).
Click hereVehicle Interior>HEATING / AIR CONDITIONING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 2 air conditioning control assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for Front)>REMOVAL
Inspect the No. 2 air conditioning control assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for Front)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear heater blower resistor.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER RESISTOR (for Rear Heater)>REMOVAL
Inspect the rear heater blower resistor.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER RESISTOR (for Rear Heater)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear heater blower motor sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REAR HEATER UNIT>DISASSEMBLY
Inspect the rear heater blower motor sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REAR HEATER UNIT>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the heater relay (HTR RR NO.1) from the No. 1 engine room relay block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal 5 - Body ground | Always | 11 to 14 V |
| Terminal 2 - Body ground | Ignition switch off | Below 1 V |
| Terminal 2 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the heater relay (HTR RR NO.1) from the No. 1 engine room relay block assembly.
Disconnect the u2 rear heater blower motor sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal 3 - u2-1 | Always | Below 1 Ω |
| Terminal 3 or u2-1 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the u1 rear heater blower resistor connector.
Disconnect the u2 rear heater blower motor sub-assembly connector.
Disconnect the N81 No. 2 air conditioning control assembly connector.
Measure the resistance according to the value(s) in the table blolw.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| u1-1 (HI) - u2-2 | Always | Below 1 Ω |
| u1-2 (M1) - Body ground | Always | Below 1 Ω |
| u1-1 (HI) or u2-2 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the u2 rear heater blower motor sub-assembly connector.
Disconnect the N81 No. 2 air conditioning control assembly connector.
Disconnect the u1 rear heater blower resistor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| u2-2 - N81-8 (HI) | Always | Below 1 Ω |
| u2-2 or N81-8 (HI) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N81 No. 2 air conditioning control assembly connector.
Disconnect the u1 rear heater blower resistor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N81-10 (M1) - u1-3 (M2) | Always | Below 1 Ω |
| N81-1 (E) - Body ground | Always | Below 1 Ω |
| N81-10 (M1) or u1-3 (M2) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the heater relay (HTR RR NO.1) from the No. 1 engine room relay block assembly.
Disconnect the N81 No. 2 air conditioning control assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N81-4 (LO) - Terminal 1 | Always | Below 1 Ω |
| N81-4 (LO) or Terminal 1 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG