Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF)
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0385516 ECD SYSTEM(w/ DPF) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P007A11  Charge Air Cooler Temperature Sensor Bank 1 Circuit Short to Ground  P007A15  Charge Air Cooler Temperature Sensor Bank 1 Circuit Short to Battery or Open  


DESCRIPTION

A283580E06
3.354,2.271 3.74,1.99 false 2.26,0.406 2.833,0.667 0.573,0.26 10 Fig. 1: 3.292,4.271 4.167,4.5 0.875,0.229 10 Temperature 2.396,0.969 2.771,1.219 0.375,0.25 10 (kΩ) 2.281,1.146 2.521,1.365 0.24,0.219 10 30 2.281,1.583 2.521,1.802 0.24,0.219 10 10 2.354,1.875 2.594,2.094 0.24,0.219 10 5 2.354,2.094 2.594,2.313 0.24,0.219 10 3 2.354,2.26 2.51,2.479 0.156,0.219 10 2 2.344,2.531 2.594,2.75 0.25,0.219 10 1 2.24,2.833 2.479,3.052 0.24,0.219 10 0.5 2.24,3.198 2.479,3.417 0.24,0.219 10 0.2 2.24,3.469 2.479,3.688 0.24,0.219 10 0.1 2.281,1.323 2.531,1.542 0.25,0.219 10 20 2.542,3.823 2.781,4.042 0.24,0.219 10 -20 2.938,3.823 3.177,4.042 0.24,0.219 10 0 3.208,3.823 3.448,4.042 0.24,0.219 10 20 3.521,3.823 3.76,4.042 0.24,0.219 10 40 3.833,3.823 4.073,4.042 0.24,0.219 10 60 4.146,3.823 4.385,4.042 0.24,0.219 10 80 4.385,3.823 4.625,4.042 0.24,0.219 10 100 2.583,4 2.823,4.219 0.24,0.219 10 -4 2.896,4 3.135,4.219 0.24,0.219 10 32 3.208,4 3.448,4.219 0.24,0.219 10 68 3.479,4 3.729,4.25 0.25,0.25 10 104 3.792,4 4.125,4.25 0.333,0.25 10 140 4.094,4 4.417,4.25 0.323,0.25 10 176 4.385,4 4.708,4.25 0.323,0.25 10 212 4.677,3.823 5,4.073 0.323,0.25 10 (°C) 4.677,4 5,4.25 0.323,0.25 10 (°F) 3.802,1.896 4.583,2.167 0.781,0.271 10 Acceptable 2.26,0.719 3.083,0.917 0.823,0.198 10 Resistance 2.24,3.021 2.479,3.24 0.24,0.219 10 0.3

The Intake Air Temperature (IAT) sensor detects the IAT after the intake air passes through the intercooler. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).

The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the IAT, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P007A11 Charge Air Cooler Temperature Sensor Bank 1 Circuit Short to Ground Short in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic).
·

Short in intake air temperature sensor (turbo) circuit

·

Intake air temperature sensor (turbo)

·

ECM


Comes on DTC stored SAE Code: P007C
P007A15 Charge Air Cooler Temperature Sensor Bank 1 Circuit Short to Battery or Open Open in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic).
·

Open in intake air temperature sensor (turbo) circuit

·

Intake air temperature sensor (turbo)

·

ECM


Comes on DTC stored SAE Code: P007D

Related Data List
DTC No. Data List
P007A11
P007A15
Intake Air Temperature B1S1 (Turbo)

HINT:

If DTC P007A11 or P007A15 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P007A11
P007A15
Ignition switch ON for 1 second or more

WIRING DIAGRAM

A337317E92
0.448,2.813 0.76,3.01 0.313,0.198 10 false E24 5.604,3.01 6.063,3.208 0.458,0.198 10 false E5 5.583,3.208 6.042,3.406 0.458,0.198 10 false ECM 0.438,3.021 2.969,3.24 2.531,0.219 10 false Intake Air Temperature Sensor (Turbo) 5.26,1.333 5.719,1.531 0.458,0.198 10 false THIA 5.26,1.917 5.781,2.115 0.521,0.198 10 false E2 2.198,1.323 2.656,1.521 0.458,0.198 10 false 2 2.208,1.927 2.667,2.125 0.458,0.198 10 false 1 5.01,1.333 5.469,1.531 0.458,0.198 10 false 26 5.021,1.927 5.479,2.125 0.458,0.198 10 false 27 5.906,0.948 6.365,1.146 0.458,0.198 10 false 5 V 5.854,1.219 6.313,1.417 0.458,0.198 10 false R 1.802,1.333 2.26,1.531 0.458,0.198 10 false THA 1.896,1.927 2.417,2.125 0.521,0.198 10 false E2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE B1S1 (TURBO))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S1 (Turbo).


d.

Read the value.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature B1S1 (Turbo)
50003 372 310
OK:

Same as air temperature near intake manifold.


Result:
Result Proceed to
-40°C (-40°F) A
190°C (374°F) or higher B
OK (same as air temperature near intake manifold) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 190°C (374°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A239705C19
0.729,3.25 1.083,3.469 0.354,0.219 1.792,3.448 2.042,3.865 true 1.448,3.448 1.198,3.885 true 0.708,1.427 1.021,1.625 0.313,0.198 10 false *1 2.667,1.375 2.979,1.573 0.313,0.198 10 false *2 2.438,0.677 2.979,0.865 0.542,0.188 10 false THIA 2.448,1.115 2.76,1.313 0.313,0.198 10 false E2 1.688,0.698 2.229,0.885 0.542,0.188 10 false THA 1.708,1.073 2.021,1.271 0.313,0.198 10 false E2 0.844,2.781 1.156,2.979 0.313,0.198 10 false *a 2.031,3.927 2.573,4.115 0.542,0.188 10 false THA 1.042,3.917 1.354,4.115 0.313,0.198 10 false E2 0.781,3.271 1.24,3.469 0.458,0.198 10 false E24
*1 Intake Air Temperature Sensor (Turbo)
*2 ECM
*a Front view of wire harness connector
(to Intake Air Temperature Sensor (Turbo))


Disconnect the intake air temperature sensor (turbo) connector.


b.

Connect terminals 1 (E2) and 2 (THA) of the intake air temperature sensor (turbo) wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S1 (Turbo).


f.

Read the value.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature B1S1 (Turbo)
50003 372 310
OK:

190°C (374°F) or higher



Result:
Proceed to
OK
NG



OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)

NG

4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Replace the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.

Disconnect the intake air temperature sensor (turbo) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E24-2 (THA) - E5-26 (THIA) Always Below 1 Ω
E24-1 (E2) - E5-27 (E2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A302633C50
0.771,0.25 1.083,0.448 0.313,0.198 10 false *1 2.604,0.25 2.917,0.448 0.313,0.198 10 false *2 2.438,1.031 2.813,1.292 0.375,0.26 10 false THIA 2.479,1.51 3.01,1.813 0.531,0.302 10 false E2
*1 Intake Air Temperature Sensor (Turbo)
*2 ECM


Disconnect the intake air temperature sensor (turbo) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S1 (Turbo).


e.

Read the value.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature B1S1 (Turbo)
50003 372 310
OK:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

8.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)

NG

10.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
8.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Replace the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON for 1 second or more.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Confirm that the DTC is not output again.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Proceed to
NEXT



NEXT

END

10.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
a.

Disconnect the intake air temperature sensor (turbo) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E24-2 (THA) or E5-26 (THIA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED