Refer to DTC P010012.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P010012
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P01009B | Mass or Volume Air Flow Sensor "A" High/Excessive Flow | After the engine is completely warmed up, while the accelerator pedal is released for 7 seconds or more and the vehicle is decelerating, the intake air volume is higher than the threshold* (EGR valve fully closed and throttle valve is fully open) (2 trip detection logic).
*: The threshold is different depending on the values of "Engine Speed", "Intake Manifold Absolute Pressure" and "Intake Air Temperature B1S1 (Turbo)". |
·
Mass air flow meter sub-assembly ·
Intake air temperature sensor (turbo) ·
Manifold absolute pressure sensor ·
Electric EGR control valve assembly ·
ECM ·
Open or short in mass air flow meter sub-assembly circuit |
Comes on | DTC stored | SAE Code: P0101 |
| P01009C | Mass or Volume Air Flow Sensor "A" Low/Insufficient Flow | After the engine is completely warmed up, while the accelerator pedal is released for 7 seconds or more and the vehicle is decelerating, the intake air volume is lower than the threshold* (EGR valve fully closed and throttle valve is fully open) (2 trip detection logic).
*: The threshold is different depending on the values of "Engine Speed", "Intake Manifold Absolute Pressure" and "Intake Air Temperature B1S1 (Turbo)". |
·
Mass air flow meter sub-assembly ·
Intake air temperature sensor (turbo) ·
Manifold absolute pressure sensor ·
Electric EGR control valve assembly ·
ECM ·
Open or short in mass air flow meter sub-assembly circuit |
Comes on | DTC stored | SAE Code: P0101 |
P01009B (High air flow rate malfunction): For example when the vehicle is decelerating and "Mass Air Flow Sensor" is 52 gm/sec or more, a high air flow malfunction is confirmed (at "Engine Speed" is 1600 rpm, "Intake Manifold Absolute Pressure" is 110 kPa and "Intake Air Temperature B1S1 (Turbo)" is 35°C).
P01009C (Low air flow rate malfunction): For example, when the vehicle is decelerating and "Mass Air Flow Sensor" is 29 gm/sec or less, a low air flow malfunction is confirmed (at "Engine Speed" is 1600 rpm, "Intake Manifold Absolute Pressure" is 110 kPa and "Intake Air Temperature B1S1 (Turbo)" is 35°C).
| DTC No. | Data List |
|---|---|
| P01009B
P01009C |
·
Mass Air Flow Sensor ·
Intake Manifold Absolute Pressure ·
Engine Speed ·
Intake Air Temp (Turbo) ·
Target EGR Valve Position No.1 ·
Actual EGR Valve Position No.1 ·
EGR Close Learning Value Bank 1 |
If DTC P01009B and/or P01009C is stored, either of the following symptoms may appear:
As the ECU mistakenly determines that there is less air than the actual intake air amount, EGR is decreased to match the target EGR.
Combustion noise worsens
As the ECU mistakenly determines that there is more air than the actual intake air amount, EGR is increased to match the target EGR:
Misfire
White smoke
Black smoke
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P01009B
P01009C |
After the engine is completely warmed up, perform the following procedure 3 times: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
After performing the above procedure, immediately stop the vehicle and confirm that "Exhaust Temperature B1S2" displays 300°C (572°F) or higher using the GTS. |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P01009B or P01009C is output | A |
| DTC P01009B or P01009C and other DTCs are output | B |
If codes other than DTC P01009B or P01009C are output, perform troubleshooting for those DTCs first.
A
B
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Check the freeze frame data.
| Result | Proceed to |
|---|---|
·
Engine speed: 1350 rpm or less ·
Mass Air Flow Sensor: 246.0 gm/sec or more |
A |
·
Engine speed: 1350 rpm or more ·
Mass Air Flow Sensor: 0.03 gm/sec or less |
|
| Except above | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Primary / Engine Speed and Mass Air Flow Sensor.
| Tester Display |
|---|
| Engine Speed |
| Mass Air Flow Sensor |
Start the engine and read the value when 30 seconds has elapsed.
| Engine Speed | Mass Air Flow Sensor |
|---|---|
| Idling | ·
0.5 to 15 gm/sec (EGR on) ·
10 to 21 gm/sec (EGR off) |
| 3000 rpm (without load) | ·
43 to 89 gm/sec (EGR on) ·
72 to 117 gm/sec (EGR off) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL
If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine.
After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
Stop the vehicle immediately after completing the above procedure.
Connect the GTS to the DLC3.
Enter the following menus: Powertrain / Engine / Data List / Exhaust Temperature B1S2.
| Tester Display |
|---|
| Exhaust Temperature B1S2 |
"Exhaust Temperature B1S2" must be 300°C or more.
If "Exhaust Temperature B1S2" is less than 300°C (572°F), perform the DTC detection drive pattern again, increasing the vehicle speed so that the exhaust gas temperature increases.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If no pending DTCs are output, proceed to the next step to check "All Readiness".
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P01009B or P01009C.
Check the DTC judgment result.
| GTS Display | Result | Proceed to |
|---|---|---|
| Pending DTC | DTC P01009B or P01009C is output | B |
| All Readiness | NORMAL | A |
| ABNORMAL | B |
If STATUS is INCOMPLETE, perform the following procedure again 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
A
B
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E20-1 (FG) - E6-31 (VG) | Always | Below 1 Ω |
| E20-2 (E2G) - E6-29 (EVG) | Always | Below 1 Ω |
| E20-1 (FG) or E6-31 (VG) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Engine Speed and Mass Air Flow Sensor.
| Tester Display |
|---|
| Engine Speed |
| Mass Air Flow Sensor |
Start the engine and read the value when 30 seconds has elapsed.
| Engine Speed | Mass Air Flow Sensor |
|---|---|
| Idling | ·
0.5 to 15 gm/sec (EGR on) ·
10 to 21 gm/sec (EGR off) |
| 3000 rpm (without load) | ·
43 to 89 gm/sec (EGR on) ·
72 to 117 gm/sec (EGR off) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Atmospheric Pressure and Intake Manifold Absolute Pressure.
Compare the values when the ignition switch is ON.
| Tester Display |
|---|
| Atmospheric Pressure |
| Intake Manifold Absolute Pressure |
Difference between "Intake Manifold Absolute Pressure" and "Atmospheric Pressure" is less than 8 kPa.
If "Intake Manifold Absolute Pressure" and "Atmospheric Pressure" have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.
Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the intake system for vacuum leakage.
Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leakage from intake system.
Check for abnormal disconnection, pipe and hose squashing, and any damage in the intake system.
Using your hand, check whether the pipes and hoses in the intake system are securely connected.
Air leaks from the intake system can be checked by applying soapy water and revving the engine.
Check for any modifications in the intake system made by the user.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Soak the engine for a long time.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature and Intake Air Temperature B1S1 (Turbo)
| Tester Display |
|---|
| Intake Air Temperature |
| Intake Air Temperature B1S1 (Turbo) |
Intake Air Temperature is the same as Intake Air Temperature B1S1 (Turbo).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position Bank 1 / Data List / Actual EGR Valve Position No.1.
When changing the Active Test value consecutively to 1, 30, 60, 90, 60, 30 and 1%, check that Actual EGR Valve Positon No.1 smoothly changes to the set opening angle.
| Active Test Display |
|---|
| Control the EGR Step Position Bank 1 |
| Data List Display |
|---|
| Actual EGR Valve Position No.1 |
Value smoothly changes to set opening angle.
Enter the following menus: Powertrain / Engine / Data List / EGR Close Learning Value Bank 1.
Read the values.
| Tester Display |
|---|
| EGR Close Learning Value Bank 1 |
0 to 1 V
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E20-1 (FG) - E6-31 (VG) | Always | Below 1 Ω |
| E20-2 (E2G) - E6-29 (EVG) | Always | Below 1 Ω |
| E20-1 (FG) or E6-31 (VG) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL
If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine.
After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
Stop the vehicle immediately after completing the above procedure.
Connect the GTS to the DLC3.
Enter the following menus: Powertrain / Engine / Data List / Exhaust Temperature B1S2.
| Tester Display |
|---|
| Exhaust Temperature B1S2 |
"Exhaust Temperature B1S2" must be 300°C or more.
If "Exhaust Temperature B1S2" is less than 300°C (572°F), perform the DTC detection drive pattern again, increasing the vehicle speed so that the exhaust gas temperature increases.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If no pending DTCs are output, proceed to the next step to check "All Readiness".
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P01009B or P01009C.
Check the DTC judgment result.
| GTS Display | Result | Proceed to |
|---|---|---|
| Pending DTC | DTC P01009B or P01009C is output | B |
| All Readiness | NORMAL | A |
| ABNORMAL | B |
If STATUS is INCOMPLETE, perform the following procedure again 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
A
B
Remove the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>REMOVAL
Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.
When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.
Do not forcibly open the valve, as it may be damaged or deformed.
When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.
When cleaning the electric EGR control valve assembly, care should be taken to prevent the ingress of cleaning solvent into the bearings of the valve shaft, and when wiping off deposits on the EGR valve, care should be taken not to push the deposits into the bearings of the valve shaft. These contaminants may adversely affect the function of the EGR valve.
When cleaning the electric EGR control valve assembly, perform initialization procedure.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION
| *1 | Gap |
| *a | OK |
| *b | NG |
Hold the electric EGR control valve assembly up to a light, and then from the side indicated by the arrow in the illustration, visually check that there is no gap between the valve and body.
No light passes through (there is no gap between the valve and body).
Light passes through part A shown in the illustration even if the valve is completely closed as there is an opening in the seal ring of the valve. This is not a problem.
If light passes through (there is a gap between the valve and body), replace the electric EGR control valve assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL
If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine.
After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
Stop the vehicle immediately after completing the above procedure.
Connect the GTS to the DLC3.
Enter the following menus: Powertrain / Engine / Data List / Exhaust Temperature B1S2.
| Tester Display |
|---|
| Exhaust Temperature B1S2 |
"Exhaust Temperature B1S2" must be 300°C or more.
If "Exhaust Temperature B1S2" is less than 300°C (572°F), perform the DTC detection drive pattern again, increasing the vehicle speed so that the exhaust gas temperature increases.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If no pending DTCs are output, proceed to the next step to check "All Readiness".
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P01009B or P01009C.
Check the DTC judgment result.
| GTS Display | Result | Proceed to |
|---|---|---|
| Pending DTC | DTC P01009B or P01009C is output | B |
| All Readiness | NORMAL | A |
| ABNORMAL | B |
If STATUS is INCOMPLETE, perform the following procedure again 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
A
B
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine.
After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
Stop the vehicle immediately after completing the above procedure.
Connect the GTS to the DLC3.
Enter the following menus: Powertrain / Engine / Data List / Exhaust Temperature B1S2.
| Tester Display |
|---|
| Exhaust Temperature B1S2 |
"Exhaust Temperature B1S2" must be 300°C or more.
If "Exhaust Temperature B1S2" is less than 300°C (572°F), perform the DTC detection drive pattern again, increasing the vehicle speed so that the exhaust gas temperature increases.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the pending DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Inspect the intake air temperature sensor (turbo).
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the intake air temperature sensor (turbo).
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the intake system.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the manifold absolute pressure sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT