Refer to DTC P010512.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P010512
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P010516 | Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Voltage Below Threshold | Manifold absolute pressure sensor output is 0 V or less for 10 seconds when the accelerator opening amount is 15% or more (2 trip detection logic). | ·
Vacuum hose connection ·
Manifold absolute pressure sensor |
Comes on | DTC stored | SAE Code: P0106 |
| P010517 | Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Voltage Above Threshold | Manifold absolute pressure sensor output is 4.9 V or higher for 10 seconds when idling the engine after warming it up (2 trip detection logic). | ·
Vacuum hose connection ·
Manifold absolute pressure sensor |
Comes on | DTC stored | SAE Code: P0106 |
| DTC No. | Data List |
|---|---|
| P010516
P010517 |
Intake Manifold Absolute Pressure |
If DTC P010516 and/or P010517 is stored, the following symptoms may appear:
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P010516
P010517 |
After warming up engine, idle engine for 10 seconds or more, and then drive vehicle under load (accelerator opening amount 15% or more) for 10 seconds |
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P010516 or P010517 is output | A |
| DTC P010516 or P010517 and other DTCs are output | B |
A
B
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART
Check the vacuum hose connections.
Vacuum hose is connected correctly and is not damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the manifold absolute pressure sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine.
After warming up the engine, idle the engine for 10 seconds or more, and then drive the vehicle under load (accelerator opening angle 15% or more) for 10 seconds or more.
Confirm that the pending DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P010516 or P010517.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE, drive the vehicle for 5 minutes, idle the engine for 5 minutes, and then check "All Readiness" again.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT