The intake air temperature sensor is built into the mass air flow meter sub-assembly and detects the intake air temperature.
A thermistor built into the sensor changes its resistance value according to the intake air temperature.
The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).
The intake air temperature sensor is connected to the ECM.
The 5 V power source voltage from the ECM is applied to the intake air temperature sensor from terminal THA via resistor R.
Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with the intake air temperature, the voltage at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability with a cold engine.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P011011 | Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Ground | Short in the intake air temperature sensor for 0.5 seconds (1 trip detection logic). | ·
Short in intake air temperature sensor circuit ·
Intake air temperature sensor (built into mass air flow meter sub-assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P0112 |
| P011015 | Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Battery or Open | Open in the intake air temperature sensor for 0.5 seconds (1 trip detection logic). | ·
Open in intake air temperature sensor circuit ·
Intake air temperature sensor (built into mass air flow meter sub-assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P0113 |
| DTC No. | Data List |
|---|---|
| P011011
P011015 |
Intake Air Temperature |
If DTC P011011 and/or P011015 is stored, the following symptoms may appear:
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
When DTC P011011 or P011015 is stored, check the intake air temperature by entering the following menus: Powertrain / Engine / Data List / Intake Air Temperature.
| GTS Displayed | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P011011
P011015 |
Ignition switch ON for 1 second or more |
Refer to DTC P010012.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P010012
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature
Read the value.
| Tester Display |
|---|
| Intake Air Temperature |
Same as actual intake air temperature.
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| OK (same as actual intake air temperature) | C |
If there is an open circuit, the GTS indicates -40°C (-40°F).
If there is a short circuit, the GTS indicates 140°C (284°F) or higher.
A
B
C
Disconnect the mass air flow meter sub-assembly connector.
| *1 | Mass Air Flow Meter Sub-assembly | *2 | ECM |
| *a | Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly) |
- | - |
Connect terminals 4 (THA) and 2 (E2G) of the mass air flow meter sub-assembly wire harness side connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature.
Read the value.
| Tester Display |
|---|
| Intake Air Temperature |
140°C (284°F) or higher
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E20-4 (THA) - E6-28 (THA) | Always | Below 1 Ω |
| E20-2 (E2G) - E6-29 (EVG) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | Mass Air Flow Meter Sub-assembly |
| *2 | ECM |
Disconnect the mass air flow meter sub-assembly connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature.
Read the value.
| Tester Display |
|---|
| Intake Air Temperature |
-40°C (-40°F)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch to ON for 1 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E20-4 (THA) or E6-28 (THA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT