The ECM monitors the microcomputer for normal operation by calculating and comparing the injection volume command values from 2 systems.
It also monitors the injector operation circuit for malfunctions by back-calculating the actual injection volume from the injection duration returned by the injector operation circuit for each cylinder and comparing it with the injection volume command value.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P02EE00 | Cylinder 1 Injector Circuit Range/Performance | When any condition below is met (1 trip detection logic):
·
Power continues to be supplied to the No. 1 cylinder injector ·
The actual injection operation status does not match the target injection volume of the No. 1 cylinder ·
The injector power duration deviates from the target injection volume of the No. 1 cylinder |
ECM | Comes on | DTC stored | SAE Code: P02EE |
| P02EF00 | Cylinder 2 Injector Circuit Range/Performance | When any condition below is met (1 trip detection logic):
·
Power continues to be supplied to the No. 2 cylinder injector ·
The actual injection operation status does not match the target injection volume of the No. 2 cylinder ·
The injector power duration deviates from the target injection volume of the No. 2 cylinder |
ECM | Comes on | DTC stored | SAE Code: P02EF |
| P02F000 | Cylinder 3 Injector Circuit Range/Performance | When any condition below is met (1 trip detection logic):
·
Power continues to be supplied to the No. 3 cylinder injector ·
The actual injection operation status does not match the target injection volume of the No. 3 cylinder ·
The injector power duration deviates from the target injection volume of the No. 3 cylinder |
ECM | Comes on | DTC stored | SAE Code: P02F0 |
| P02F100 | Cylinder 4 Injector Circuit Range/Performance | When any condition below is met (1 trip detection logic):
·
Power continues to be supplied to the No. 4 cylinder injector ·
The actual injection operation status does not match the target injection volume of the No. 4 cylinder ·
The injector power duration deviates from the target injection volume of the No. 4 cylinder |
ECM | Comes on | DTC stored | SAE Code: P02F1 |
| P060694 | Control Module Processor Unexpected Operation | When any condition below is met (1 trip detection logic):
·
A malfunction is detected in the "accelerator pedal recognition value" used for calculating the target injection volume ·
A malfunction is detected in the "minimum engine torque" used for calculating the target injection volume ·
A malfunction is detected where the target injection volume is larger than the original target |
ECM | Comes on | DTC stored | SAE Code: P0606 |
| P062D00 | Fuel Injector Driver Circuit Performance Bank 1 | A malfunction is detected in the function that stops injection as a fail-safe during a fuel injection control malfunction (1 trip detection logic) | ECM | Comes on | DTC stored | SAE Code: P062D |
| DTC No. | Data List |
|---|---|
| P02EE00
P02EF00 P02F000 P02F100 |
·
Injection Control Malfunction (Injector Current-Carrying Time 1) ·
Injection Control Malfunction (Injector Current-Carrying Time 2) ·
Injection Control Malfunction (Injector Current-Carrying Time 3) |
| P060694 | ·
Injection Control Malfunction (Target Injection Volume 1) ·
Injection Control Malfunction (Target Injection Volume 2) ·
Injection Control Malfunction (Target Injection Volume 3) |
| P062D00 | Injection Control Malfunction (Fail Safe Function) |
The ECM calculates and compares the injection volume command value from 2 systems, and stores P060694 if the accelerator pedal recognition value, minimum engine torque or target injection volume is higher than the original target.
The ECU back calculates the actual injection volume from the injection duration returned by the injector operation circuit for each cylinder. When power continues to be supplied to the injector even if there is no injection volume command, the injection operation status does not match the target injection volume, or the injector power duration deviates from the target injection volume, P02EE00, P02EF00, P02F000 or P02F100 is stored.
P062D00 is stored if a malfunction is detected in the fail-safe function (that stops injection) during a fuel injection control malfunction.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P02EE00
P02EF00 P02F000 P02F100 P060694 |
Start the engine and idle the engine for 5 seconds or more |
| P062D00 | Start the engine, and then turn the ignition switch off to stop the engine |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P02EE00, P02EF00, P02F000, P02F100, P060694 and/or P062D00 is output | A |
| DTC P02EE00, P02EF00, P02F000, P02F100, P060694 and/or P062D00 and other DTCs are output | B |
If any DTCs other than P02EE00, P02EF00, P02F000, P02F100, P060694 and/or P062D00 are output, troubleshoot those DTCs first.
A
B
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine and wait for 10 seconds or more.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
If no pending DTC is output, the repair has been successfully completed.
| Proceed to |
|---|
| NEXT |
NEXT