The EGR valve position sensor is mounted on the electric EGR control valve assembly and used for detecting the EGR valve angle. The EGR valve angle detected by the sensor is sent to the ECM as feedback. The ECM then regulates the EGR valve angle in accordance with engine running conditions.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P040911 | Exhaust Gas Recirculation Sensor "A" Circuit Short to Ground | EGR valve position sensor output voltage is less than 0.2 V for 2 seconds (1 trip detection logic). | ·
Open or short in EGR valve position sensor circuit ·
Electric EGR control valve assembly (EGR valve position sensor) ·
ECM |
Comes on | DTC stored | SAE Code: P0405 |
| P040915 | Exhaust Gas Recirculation Sensor "A" Circuit Short to Battery or Open | EGR valve position sensor output voltage is higher than 4.8 V for 2 seconds (1 trip detection logic). | ·
Open or short in EGR valve position sensor circuit ·
Electric EGR control valve assembly (EGR valve position sensor) ·
ECM |
Comes on | DTC stored | SAE Code: P0406 |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P040911
P040915 |
Ignition switch ON for 2 seconds or more |
When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.2 to 4.8 V for more than 2 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.
Refer to DTC P040371.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P040371
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E7-31 (VCEG) - E7-24 (EEGL) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E7-25 (EGRA) - E7-24 (EEGL) | Ignition switch ON | 0.6 to 1.4 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON for 2 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>CHECK FOR INTERMITTENT PROBLEMS
| *a | Front view of wire harness connector
(to Electric EGR Control Valve Assembly) |
Disconnect the electric EGR control valve assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E33-3 (VC) - E33-1 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the electric EGR control valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E33-3 (VC) - E7-31 (VCEG) | Always | Below 1 Ω |
| E33-2 (VTA) - E7-25 (EGRA) | Always | Below 1 Ω |
| E33-1 (E2) - E7-24 (EEGL) | Always | Below 1 Ω |
| E33-3 (VC) or E7-31 (VCEG) - Body ground and other terminals | Always | 10 kΩ or higher |
| E33-2 (VTA) or E7-25 (EGRA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the electric EGR control valve assembly connector.
| *a | Front view of wire harness connector
(to Electric EGR Control Valve Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E33-3 (VC) - E33-2 (VTA) | Ignition switch off | No short or no open circuit |
| E33-2 (VTA) - E33-1 (E2) | Ignition switch off | No short or no open circuit |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch to ON for 2 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT