Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF)
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0385516 ECD SYSTEM(w/ DPF) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P060647  Control Module Processor Watchdog/Safety MCU Failure  P060747  Control Module Performance Bank 1 Watchdog/Safety MCU Failure  P060787  Control Module Performance Bank 1 Missing Message  P060D49  Internal Control Module Accelerator Pedal Position Performance Internal Electronic Failure  P160700  Cruise Control Input Processor  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P060647 Control Module Processor Watchdog/Safety MCU Failure ECM internal error continues for 1 second (1 trip detection logic). ECM Comes on DTC stored SAE Code: P0606
P060747 Control Module Performance Bank 1 Watchdog/Safety MCU Failure ECM monitor IC malfunction (1 trip detection logic). ECM Comes on DTC stored SAE Code: P0607
P060787 Control Module Performance Bank 1 Missing Message ECM monitor IC malfunction (1 trip detection logic). ECM Comes on DTC stored SAE Code: P0607
P060D49 Internal Control Module Accelerator Pedal Position Performance Internal Electronic Failure Either of the following conditions is met (1 trip detection logic):
·

There is an ECM main CPU error.

·

There is an ECM sub CPU error.


ECM Comes on DTC stored SAE Code: P060D
P160700 Cruise Control Input Processor ECM internal error continues for 1 second (1 trip detection logic). ECM Comes on DTC stored SAE Code: P1607

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P060647
P060747
P060787
P060D49
P160700
Ignition switch ON for 1 second or more

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

d.

Turn the ignition switch off for 30 seconds or more.


e.

Turn the ignition switch to ON for 1 second or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

g.

Read the DTCs.

Result:
Result Proceed to
DTC P060647, P060747, P60787, P060D49 and/or P160700 is output A
No DTC is output B




A

2.REPLACE ECM

B

2.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON for 1 second or more.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END