Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF)
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0385516 ECD SYSTEM(w/ DPF) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P062F00  Internal Control Module EEPROM Error  P062F46  Internal Control Module EEPROM Calibration/Parameter Memory Failure  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P062F00 Internal Control Module EEPROM Error When any condition below is met (1 trip detection logic):
·

Injector compensation code is not registered.

·

Wrong injector compensation code is registered.


·

Injector compensation code

·

Injector pilot quantity learning value

·

ECM


Comes on DTC stored SAE Code: P062F
P062F46 Internal Control Module EEPROM Calibration/Parameter Memory Failure Injector pilot quantity learning value is not registered (1 trip detection logic). Injector pilot quantity learning value Comes on DTC stored SAE Code: P062F

NOTICE:
·

When an injector assembly is replaced, the new injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.

·

Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly. If an incorrect injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

·

When an injector assembly is replaced, perform pilot quantity learning. When the ECM is replaced, all of the existing injector pilot quantity learning values must be input into the new ECM.



HINT:
·

When the ECM is replaced with a new one, P062F00 is stored because the injector compensation code has not yet been input correctly and P062F46 is stored because pilot quantity learning has not yet been completed.

·

When the injector compensation code is re-entered, the pilot quantity learning value is reset. Therefore, when the injector compensation code is re-entered after work such as injector assembly replacement is performed, P062F46 will be output.



When replacing the ECM with a new one, input all learning values and codes into the new ECM as follows:


a.

Prior to replacing the ECM, use the GTS to read and save each learning value and code from the original ECM.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION


b.

After installing a new ECM, input the saved learning values and codes into the new ECM using the GTS.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION


c.

Turn the ignition switch off and turn the GTS off.


d.

Wait for at least 30 seconds.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Clear DTC P062F00 and P062F46 stored in the ECM using the GTS.

Powertrain > Engine > Clear DTCs
50002 372
HINT:
·

Each injector assembly has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each injector assembly.

·

When you first turn ON the ignition switch after replacing the ECM and other component(s), DTC P062F00 and/or P062F46 is stored. Manually clear the DTC upon completion of compensation code registration.

Replacement Part Utility Item
ECM
·

Learning Values Save

(Click here)

·

Learning Values Write

(Click here)


Injector Assembly
·

Input Injector Compensation Code

(Click here)

·

Pilot Quantity Learning

(Click here)







CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P062F00
P062F46
Ignition switch ON for 1 second

CAUTION / NOTICE / HINT

NOTICE:
·
·

After replacing the fuel supply pump assembly, the ECM needs initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Read the DTCs.

Result:
Result Proceed to
DTC P062F00 is output A
DTC P062F00 and P062F46 is output
DTC P062F46 is output B




A

2.LEARNING VALUES CONFIRMATION

B

11.PERFORM PILOT QUANTITY LEARNING
2.LEARNING VALUES CONFIRMATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine / Utility / Learning Values Confirmation.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Learning Values Confirmation
50005 372 4599
Result:
Result Proceed to
The injector compensation codes are not input A
The injector compensation codes registered in the ECM are different than the codes imprinted on the injector assemblies B
Except above C




A

3.PERFORM LEARNING VALUES SAVE

B

10.REGISTER INJECTOR COMPENSATION CODE

C

12.LEARNING VALUES CONFIRMATION
3.PERFORM LEARNING VALUES SAVE
a.

Install the old ECM.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Learning Values Save.

Powertrain > Engine > Utility
Tester Display
Learning Values Save
50005 372 4597


Result:
Result Proceed to
Learning Values Save is complete A
Learning Values Save is failed B



A

4.PERFORM LEARNING VALUES WRITE

B

10.REGISTER INJECTOR COMPENSATION CODE
4.PERFORM LEARNING VALUES WRITE
a.

Remove the old ECM.


b.

Install a new ECM.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Learning Values Write.

Powertrain > Engine > Utility
Tester Display
Learning Values Write
50005 372 4598


Result:
Result Proceed to
Learning Values Write is complete A
Learning Values Write is fail B



A

5.CHECK DTC OUTPUT

B

8.PERFORM LEARNING VALUES SAVE
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and leave the vehicle for 30 seconds or more.


d.

Turn the ignition switch to ON for 1 second.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

f.

Read the DTCs.

Result:
Result Proceed to
No DTC is output A
DTC P062F00 and/or P062F46 is output B




A

END

B

6.REPLACE ECM
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and leave the vehicle for 30 seconds or more.


d.

Turn the ignition switch to ON for 1 second.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

8.PERFORM LEARNING VALUES SAVE
a.

Remove the new ECM.


b.

Install the old ECM.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Learning Values Save.

Powertrain > Engine > Utility
Tester Display
Learning Values Save
50005 372 4597


Result:
Proceed to
NEXT



NEXT

9.PERFORM LEARNING VALUES WRITE
9.PERFORM LEARNING VALUES WRITE
a.

Remove the old ECM.


b.

Install a new ECM.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Learning Values Write.

Powertrain > Engine > Utility
Tester Display
Learning Values Write
50005 372 4598


Result:
Result Proceed to
Learning Values Write is complete A
Learning Values Write is failed B



A

5.CHECK DTC OUTPUT

B

10.REGISTER INJECTOR COMPENSATION CODE
10.REGISTER INJECTOR COMPENSATION CODE
a.

Register the injector compensation code.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Injector Compensation
50005 372 4596

Result:
Proceed to
NEXT



NEXT

11.PERFORM PILOT QUANTITY LEARNING
11.PERFORM PILOT QUANTITY LEARNING
a.

Perform the pilot quantity learning.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Pilot Quantity Learning
50005 372 4569

Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
12.LEARNING VALUES CONFIRMATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine / Utility / Learning Values Confirmation.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Learning Values Confirmation
50005 372 4599
Result:
Result Proceed to
The pilot quantity learning values are set to the default values A
Except above B


HINT:

When the pilot quantity learning values are set to the default values, "7FFF" is displayed.




A

11.PERFORM PILOT QUANTITY LEARNING

B

5.CHECK DTC OUTPUT