Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF)
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0385516 ECD SYSTEM(w/ DPF) J

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  Starter Signal Circuit  


DESCRIPTION

w/o Stop and Start System

While the engine is being cranked, the starter signal is also sent to terminal STA of the ECM. The starter signal mainly performs engine control when the engine is started.

w/ Stop and Start System

While the engine is being cranked, the ECM detects the starter drive signal (STA2 signal) from the engine stop and start ECU as the starter operation signal (STA signal) to perform engine control when the engine is started.

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·
·

Read Starter Count before replacing the engine stop and start ECU, perform the replacement procedure, and then write Starter Count to the newly installed engine stop and start ECU.

·

When replacing the engine stop and start ECU or the air conditioning amplifier assembly, initialize and learn the engine stop and start ECU air conditioning information.

·

When replacing the engine stop and start ECU or airbag ECU assembly (G sensor), initialize and learn the engine stop and start ECU G sensor zero point learned information.



HINT:

w/o Stop and Start System

This procedure is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to the problem symptoms table.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>PROBLEM SYMPTOMS TABLE


PROCEDURE

1.CHECK IF VEHICLE IS EQUIPPED WITH STOP AND START SYSTEM
a.

Confirm the vehicle specifications.

Result:
Result
w/ Stop and Start System
w/o Stop and Start System




w/o Stop and Start System

2.READ VALUE USING GTS (STARTER SW)

w/ Stop and Start System

4.CHECK WHETHER ENGINE CAN BE CRANKED
2.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Primary / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.


OK:
Switch Condition Starter SW
ON OFF
START ON


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (ECM - CLUTCH START SWITCH ASSEMBLY OR PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (ECM - CLUTCH START SWITCH ASSEMBLY OR PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the clutch start switch assembly connector.*1


c.

Disconnect the park/neutral position switch assembly connector.*2


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-22 (STA) - M7-2 (L)*1 Always Below 1 Ω
N2-22 (STA) - E92-5 (L)*2 Always Below 1 Ω
N2-22 (STA) or M7-2 (L)*1 - Body ground and other terminals Always 10 kΩ or higher
N2-22 (STA) or E92-5 (L)*2 - Body ground and other terminals Always 10 kΩ or higher


*1: for Manual Transmission

*2: for Automatic Transmission



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.


Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B



A

5.READ VALUE USING GTS (STARTER SW)

B

7.READ VALUE USING GTS (STARTER SW)
5.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Primary / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Check the value displayed on the GTS when the ignition switch is ON and the engine stars.


OK:
Switch Condition Starter SW
ON OFF
START ON


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM)

NG

GO TO STOP AND START SYSTEM (STARTER SIGNAL CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM)
a.

Disconnect the engine stop and start ECM connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N32-23 (STA2) - N2-22 (STA) Always Below 1 Ω
N32-23 (STA2) or N2-22 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

GO TO STOP AND START SYSTEM (STA SIGNAL CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Primary / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Check the value displayed on the GTS when the ignition switch is ON and the engine stars.


OK:
Switch Condition Starter SW
ON OFF
START ON


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER NO. 2 RELAY - ECM)