Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR Cooler)
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0388652 ECD SYSTEM(w/o EGR Cooler) D

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  DIAGNOSIS SYSTEM  


EURO-OBD (EUROPEAN SPEC)


A208456

When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, an OBD scan tool (complying with ISO 15765-4) must be connected to the vehicle. Various data output from the vehicle's ECM can then be read.

Euro-OBD regulations require that the vehicle's on-board computer illuminate the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:

1.

The emission control system components.

2.

The powertrain control components which affect vehicle emissions.

3.

The computer


In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are stored in the ECM memory. If the malfunction does not reoccur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain stored in the ECM memory.

To check DTCs, connect the GTS or OBD scan tool to the Data Link Connector 3 (DLC3) of the vehicle.

The scan tool displays DTCs, the Freeze Frame Data and a variety of engine data.

The DTCs and Freeze Frame Data can be cleared using the scan tool.


M-OBD (EXCEPT EUROPEAN SPEC.)


A208456

When troubleshooting a Multiplex On-Board Diagnostic (M-OBD) vehicle, the vehicle must be connected to the GTS. Various data output from the ECM can then be read.

OBD regulations require that the vehicle on-board computer illuminate the MIL on the instrument panel when the computer detects a malfunction in:

1.

The emission control system components.

2.

The powertrain control components which affect vehicle emissions.

3.

The computer.


In addition, the applicable Diagnostic Trouble Codes (DTCs) are stored in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain stored in the ECM memory.


NORMAL MODE AND CHECK MODE


The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2 trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1 trip detection logic" is used when simulating malfunction symptoms to increase the ability of the system to detect malfunctions, including intermittent malfunctions (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>CHECK MODE PROCEDURE).


2 TRIP DETECTION LOGIC


When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the next subsequent drive cycle, the MIL is illuminated (2nd trip).


FREEZE FRAME DATA


The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


BATTERY VOLTAGE


Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding.


MIL


a.
A208456

The MIL illuminates when the ignition switch is turned to ON and the engine is not running.

HINT:

If the MIL is not illuminated, check the MIL circuit (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>MIL Circuit).



b.

When the engine is started, the MIL should turn off. If the MIL remains on, the diagnosis system has detected a malfunction or abnormality in the ECD system.



ALL READINESS


HINT:
·

With "All Readiness", you can use the GTS to check whether or not the DTC judgment has been completed.

·

You should check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Perform the DTC judgment driving pattern to run the DTC judgment.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

j.

Input the DTCs to be confirmed.


k.

Check the DTC judgment result.

Result
GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving after confirming DTC enabling conditions





DIAGNOSIS RELATED INFORMATION


HINT:
·

If the detection conditions of certain DTCs are met before a malfunction can be confirmed, the ECM will store Diagnosis Related Information. Vehicle condition information from when the detection conditions were met can be checked using the Diagnosis Related Information. Diagnosis Related Information should be used as a reference only, and should not be relied upon solely when determining whether a part is faulty or not.

·

Clearing DTCs will also clear Diagnosis Related Information.

·

DTCs and Diagnosis Related Information are saved in the GTS at the same time.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Diagnosis Related Information.

Powertrain > Engine > Utility
Tester Display
Diagnosis Related Information
50005 372 56

e.

Select a Diagnosis Related Information item to display its details.