Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners or solvents.
In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.
To prevent burns, do not remove the oil pan drain plug and oil filter sub-assembly while the engine is hot.
51447D
1.REMOVE CENTER NO. 4 ENGINE UNDER COVER
Remove the 5 bolts and center No. 4 engine under cover.
2.REMOVE NO. 4 ENGINE UNDER COVER LH
Detach the clip and remove the 2 bolt, screw and No. 4 engine under cover LH.
3.DRAIN ENGINE OIL
To prevent burns, do not remove the oil pan drain plug while the engine is hot.
Remove the oil filler cap assembly.
Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.
Clean and install a new gasket and the oil pan drain plug.
15601
4.REMOVE OIL FILTER SUB-ASSEMBLY
To prevent burns, do not remove the oil filter sub-assembly while the engine is hot.
Using SST, remove the oil filter sub-assembly.
Before removing the oil filter sub-assembly, place cloth where the oil may splash.
Use a container to catch the draining engine oil.
15601
5.INSTALL OIL FILTER SUB-ASSEMBLY
Check and clean the oil filter sub-assembly installation surface.
Apply clean engine oil to the gasket of a new oil filter sub-assembly.
Lightly screw the oil filter sub-assembly into place by hand. Tighten it until the gasket contacts the seat.
Using SST, tighten the oil filter sub-assembly.
|
3/4 Turn | - | - |
Depending on the space available, choose from the following.
If enough space is available, use a torque wrench to tighten the oil filter sub-assembly.
If enough space is not available to use a torque wrench, tighten the oil filter sub-assembly 3/4 of a turn by hand or with a common wrench.
6.ADD ENGINE OIL
Add new engine oil and install the oil filler cap assembly.
| Item | Oil Grade | Oil Viscosity (SAE) |
|---|---|---|
| w/ EGR Cooler with DPF | ACEA C2 | - 0W-30
- 5W-30 |
·
w/ EGR Cooler without DPF ·
w/o EGR Cooler with Laminated EGR Pre-Cooler |
API CF-4, CF or ACEA-B3, B4, B5 or JASO DL-0 | - 5W-30
- 10W-30 - 15W-40 |
| w/o EGR Cooler | API CF-4, CF or ACEA-B3, B4, B5 or JASO DL-0 | - 5W-30
- 10W-30 - 15W-40 - 20W-50 |
| Item | Specified Condition |
|---|---|
| Drain and refill without oil filter sub-assembly change | 6.6 liters (7.0 US qts, 5.8 Imp. qts) |
| Drain and refill with oil filter sub-assembly change | 7.1 liters (7.5 US qts, 6.2 Imp. qts) |
| Dry fill | 7.6 liters (8.0 US qts, 6.7 Imp. qts) |
7.INSPECT FOR OIL LEAK
Start the engine. Make sure that there are no oil leaks from the areas that were worked on.
8.INSPECT ENGINE OIL LEVEL
9.INSTALL NO. 4 ENGINE UNDER COVER LH
Attach the clip and install the No. 4 engine under cover LH with the 2 bolts and screw.
51447D
10.INSTALL CENTER NO. 4 ENGINE UNDER COVER
Install the center No. 4 engine under cover with the 5 bolts.