Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ EGR Cooler)
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0388653 ECD SYSTEM(w/ EGR Cooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  P011C62  Charge Air Cooler Temperature/Intake Air Temperature Bank 1 Signal Compare Failure  


DESCRIPTION

Refer to DTC P007A11.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>P007A11

Refer to DTC P011011.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>P011011

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P011C62 Charge Air Cooler Temperature/Intake Air Temperature Bank 1 Signal Compare Failure After the engine is completely warmed up and then allowed to soak for a long time (10 hours or more), the difference in temperature at the intake air temperature sensor and intake air temperature sensor (turbo) after turbocharger after idling for 3 minutes is 25°C (77°F) or higher (2 trip detection logic).
·

Open or short in intake air temperature sensor circuit

·

Open or short in intake air temperature sensor (turbo) circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

Intake air temperature sensor (turbo)

·

ECM


Comes on DTC stored SAE Code: P011C

Related Data List
DTC No. Data List
P011C62
·

Intake Air Temperature

·

Intake Air Temperature B1S1 (Turbo)



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P011C62 After engine completely warmed up, allow engine to soak for long time (10 hours or more).
Start the engine and idle the engine for 3 minutes or more.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P011C62)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Read the DTCs.

Result:
Result Proceed to
DTC P011C62 is output A
DTC P011C62 and other DTCs are output B




A

2.READ VALUE USING GTS (COOLANT TEMPERATURE)

B

2.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Allow the engine to soak for 1 to 2 hours.

HINT:
·

It is not necessary to allow the engine to soak if the engine is cold.

·

The engine cools faster if the hood is opened.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205

e.

Read the value.

OK:

The difference between the displayed value and outside air temperature is below 5°C (41°F).


NOTICE:

If the difference between "Coolant Temperature" and the outside air temperature is 5°C (41°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.



Result:
Proceed to
NEXT



NEXT

3.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
3.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature
50003 372 214

d.

Read the value.

OK:

The difference between the displayed value and outside air temperature is below 25°C (77°F).



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (INTAKE AIR TEMPERATURE B1S1 (TURBO))

NG

10.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
4.READ VALUE USING GTS (INTAKE AIR TEMPERATURE B1S1 (TURBO))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S1 (Turbo).

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature B1S1 (Turbo)
50003 372 310

d.

Read the value.

OK:

The difference between the displayed value and outside air temperature is below 25°C (77°F).



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

6.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
a.

Disconnect the intake air temperature sensor (turbo) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E24-2 (THA) - E5-26 (THIA) Always Below 1 Ω
E24-1 (E2) - E5-27 (E2) Always Below 1 Ω
E24-2 (THA) or E5-26 (THIA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Replace the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Allow the engine to soak for 1 to 2 hours.

HINT:
·

It is not necessary to allow the engine to soak if the engine is cold.

·

The engine cools faster if the hood is opened.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205

e.

Read the value.

NOTICE:

If the difference between "Coolant Temperature" and the outside air temperature is 5°C (41°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.



f.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature and Intake Air Temperature B1S1 (Turbo).

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature
Intake Air Temperature B1S1 (Turbo)
50003 372 214,310

g.

Read the value.

OK:

The difference between the displayed value and outside air temperature is below 25°C (77°F).



Result:
Proceed to
NEXT



NEXT

END

10.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E20-4 (THA) - E6-28 (THA) Always Below 1 Ω
E20-2 (E2G) - E6-29 (EVG) Always Below 1 Ω
E20-4 (THA) or E6-28 (THA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED