Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ EGR Cooler)
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0388653 ECD SYSTEM(w/ EGR Cooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  P03402A  Camshaft Position Sensor "A" Bank 1 or Single Sensor Signal Stuck in Range  P034031  Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal  


DESCRIPTION

The camshaft position sensor (G2 signal) consists of a magnet and MRE (Magneto-Resistive Element).

The G2 signal plate has 3 teeth on its outer circumference and is installed on the exhaust camshaft. When the camshaft rotates, the protrusion on the signal plate and the air gap on the MRE change, causing fluctuations in the magnetic field that generate a voltage in the MRE.

The NE signal plate has 34 teeth and is mounted on the crankshaft angle sensor plate. The NE signal sensor generates 34 signals for every revolution. The ECM detects the camshaft angle based on the G2 signal, and detects the crankshaft angle based on the NE signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P03402A Camshaft Position Sensor "A" Bank 1 or Single Sensor Signal Stuck in Range No camshaft position sensor signal is sent to the ECM while cranking for 4 seconds or more (1 trip detection logic).
·

Camshaft position sensor

·

Exhaust camshaft

·

ECM


Comes on DTC stored SAE Code: P0340
P034031 Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal Camshaft position sensor signal is not input with an engine speed of 650 rpm or more (1 trip detection logic).
·

Camshaft position sensor

·

Exhaust camshaft

·

ECM


Comes on DTC stored SAE Code: P0340

HINT:

If DTC P03402A or P034031 is stored, the following symptoms may appear:

-

Difficulty starting

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power




Reference: Inspection using an oscilloscope.

HINT:
A340471E01
3.042,1.021 3.375,1.281 0.333,0.26 10 false GND 3.031,1.542 3.365,1.771 0.333,0.229 10 false GND 0.052,0.854 0.406,1.094 0.354,0.24 10 false G2 0.063,1.396 0.354,1.625 0.292,0.229 10 false NE 2.729,0.156 3.323,0.354 0.594,0.198 10 false 2 V/DIV. 1.292,1.833 2.5,2 1.208,0.167 10 false 20 msec./DIV.

The correct waveform is as shown.


ECM Terminal Name Between G2+ and G2-
Between NE+ and NE-
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P03402A Crank engine for 4 seconds (STA on)
P034031 Idling for 5 second or more (STA off)

WIRING DIAGRAM

A348533E20
0.938,2.01 2.677,2.219 1.74,0.208 10 false Camshaft Position Sensor 0.875,4.063 2.708,4.271 1.833,0.208 10 false Crankshaft Position Sensor 5.167,4.156 5.604,4.344 0.438,0.188 10 false ECM 2.229,0.906 2.427,1.083 0.198,0.177 10 false 3 1.938,0.781 2.229,0.979 0.292,0.198 10 false VC 1.896,3.104 2.25,3.302 0.354,0.198 10 false NE- 2.229,1.281 2.427,1.458 0.198,0.177 10 false 2 2.219,1.646 2.417,1.823 0.198,0.177 10 false 1 2.229,2.875 2.427,3.052 0.198,0.177 10 false 3 2.229,3.24 2.427,3.417 0.198,0.177 10 false 2 2.219,3.615 2.417,3.792 0.198,0.177 10 false 1 5.208,3.99 5.5,4.188 0.292,0.198 10 false E8 0.948,1.833 1.583,2.094 0.635,0.26 10 false E79 0.885,3.885 1.604,4.198 0.719,0.313 10 false E104 4.708,0.802 5.156,1.021 0.448,0.219 10 false VCG 1.844,1.156 2.292,1.354 0.448,0.198 10 false G22- 4.698,1.156 5.146,1.354 0.448,0.198 10 false G2- 1.802,1.521 2.344,1.719 0.542,0.198 10 false G22+ 4.688,1.521 5.229,1.719 0.542,0.198 10 false G2+ 1.927,2.76 2.219,2.958 0.292,0.198 10 false VC 4.677,2.76 5.271,2.948 0.594,0.188 10 false VCNE 4.688,3.125 5.042,3.323 0.354,0.198 10 false NE- 1.875,3.469 2.271,3.667 0.396,0.198 10 false NE+ 4.688,3.479 5.083,3.677 0.396,0.198 10 false NE+ 4.448,0.885 4.677,1.063 0.229,0.177 10 false 17 4.438,1.271 4.635,1.448 0.198,0.177 10 false 18 4.438,1.646 4.677,1.823 0.24,0.177 10 false 27 4.438,2.865 4.635,3.042 0.198,0.177 10 false 20 4.438,3.24 4.635,3.417 0.198,0.177 10 false 19 4.438,3.594 4.635,3.771 0.198,0.177 10 false 28

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.

Result:
Result Proceed to
Cranking is OK. A
Does not crank at all. B




A

2.INSPECT ECM (CAMSHAFT POSITION SENSOR)

B

2.INSPECT ECM (CAMSHAFT POSITION SENSOR)
a.

Inspect the ECM using an oscilloscope.

i.

While the engine is idling, check the waveform between the terminals of the ECM connector.

A346512C20
5.531,0.198 5.958,0.51 0.427,0.313 6.229,1.417 5.927,0.938 true 5.688,1.375 5.885,0.948 true 5.26,1.417 5.854,0.896 true 5.896,0.896 6.302,0.313 6.302,0.313 6.438,0.313 true 3.438,0.792 3.771,0.99 0.333,0.198 10 false GND 0.104,0.708 0.406,0.917 0.302,0.208 10 false G2 0.073,1.063 0.354,1.26 0.281,0.198 10 false NE 3.438,1.25 3.771,1.448 0.333,0.198 10 false GND 3.323,0.073 3.854,0.271 0.531,0.198 10 false 2 V/DIV. 1.385,1.49 2.625,1.688 1.24,0.198 10 false 20 msec./DIV. 5.5,1.427 6.135,1.656 0.635,0.229 10 false 28 (NE+) 4.74,1.427 5.333,1.677 0.594,0.25 10 false 19 (NE-) 5.615,0.281 5.948,0.469 0.333,0.188 10 false E8 6.25,1.427 6.938,1.656 0.688,0.229 10 false 27 (G2+) 6.479,0.24 7.021,0.438 0.542,0.198 10 false 18 (G2-) 4.208,0.073 4.542,0.26 0.333,0.188 10 false *a
*a Component with harness connected
(ECM)
- -


OK:
Tester Connection Tester Range Condition Specified Condition
E8-27 (G2+) - E8-18 (G2-) 2 V/DIV.
20 msec./DIV.
Idling Correct waveform as shown in illustration
E8-28 (NE+) - E8-19 (NE-) 2 V/DIV.
20 msec./DIV.
Idling Correct waveform as shown in illustration




Result:
Proceed to
OK
NG



OK

3.INSPECT CAMSHAFT POSITION SENSOR AND CRANKSHAFT POSITION SENSOR TIMING

NG

7.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)
3.INSPECT CAMSHAFT POSITION SENSOR AND CRANKSHAFT POSITION SENSOR TIMING
a.

Inspect the ECM using an oscilloscope.


b.

While the engine is idling, check the waveform between the terminals of the ECM connector.


c.

Inspect the camshaft position sensor and crankshaft position sensor timing.

HINT:

The G2 signal is output 3 times for every 2 crankshaft rotations (720°CA).


A348543E01
5.885,1.25 6.344,1.448 0.458,0.198 10 false GND 5.896,1.948 6.354,2.146 0.458,0.198 10 false GND 0.625,1.031 1.406,1.219 0.781,0.188 10 false G2 Signal 0.615,1.719 1.354,1.906 0.74,0.188 10 false Ne Signal 5.906,0.438 6.646,0.625 0.74,0.188 10 false 2 V/DIV. 3.094,2.417 4.167,2.604 1.073,0.188 10 false 20 msec./DIV. 3.302,0.26 4.073,0.521 0.771,0.26 10 false 720°CA

OK:
Tester Connection Tester Range Condition Specified Condition
E8-27 (G2+) - E8-18 (G2-) 2 V/DIV.
20 msec./DIV.
Idling Correct waveform as shown in illustration
E8-28 (NE+) - E8-19 (NE-) 2 V/DIV.
20 msec./DIV.
Idling Correct waveform as shown in illustration



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

6.CHECK ENGINE MECHANICAL SYSTEM
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off for 30 seconds or more.


f.

Start the engine and idle it for 5 seconds or more.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Read the DTCs.

Result:
Result Proceed to
DTC P03402A or P034031 is output A
DTC is not output B




A

5.REPLACE ECM

B

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK ENGINE MECHANICAL SYSTEM
a.

When the G2 signal appears to be malfunctioning, check the exhaust camshaft.

·

If the teeth of the timing rotor are damaged, perform replacement.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>CAMSHAFT (w/ EGR Cooler)>REMOVAL



b.

When the Ne signal appears to be malfunctioning, check the following parts.

·

Installation condition of the crankshaft position sensor

·

Crank angle sensor plate



c.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.
A316078C04
2.469,0.604 2.781,0.76 0.313,0.156 10 false *a 0.448,2.646 0.76,2.844 0.313,0.198 10 false OK 0.479,0.635 0.792,0.833 0.313,0.198 10 false NG
*a Clearance


Check the camshaft position sensor installation.

OK:

Camshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

8.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)

NG

12.SECURELY REINSTALL CAMSHAFT POSITION SENSOR
8.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)
a.

Inspect the timing rotor of the exhaust camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

9.REPLACE CAMSHAFT POSITION SENSOR

NG

11.REPLACE EXHAUST CAMSHAFT
9.REPLACE CAMSHAFT POSITION SENSOR

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off for 30 seconds or more.


f.

Start the engine and idle it for 5 seconds or more.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END

11.REPLACE EXHAUST CAMSHAFT

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.SECURELY REINSTALL CAMSHAFT POSITION SENSOR
a.

Securely reinstall the camshaft position sensor.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>INSTALLATION


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED