Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ EGR Cooler) › 2019.02–2019.06
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0388653 ECD SYSTEM(w/ EGR Cooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  P061512  Starter Relay Circuit Short to Battery  


DESCRIPTION

While the engine is being cranked, the ECM detects the starter signal (STA signal) and performs engine control when the engine starts.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) or more for more than 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P061512 Starter Relay Circuit Short to Battery Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):

(a) Vehicle speed is more than 20 km/h (12.4 mph).

(b) Engine speed is more than 1000 rpm.

(c) STA signal is on.


·

STARTER relay

·

Park/Neutral position switch assembly*1

·

Clutch start switch assembly*2

·

STA signal circuit

·

ECM


Comes on DTC stored SAE Code: P0617

·

*1: for Automatic transmission

·

*2: for Manual transmission


Related Data List
DTC No. Data List
P061512 Starter SW

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P061512 Drive the vehicle for 20 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more

WIRING DIAGRAM

A444450E02
0.625,1.198 1.156,1.448 0.531,0.25 10 false N28 0.635,1.365 2.24,1.594 1.604,0.229 10 false Ignition Switch Assembly 0.542,0.667 0.854,0.865 0.313,0.198 10 false 1 1.823,0.667 2.135,0.865 0.313,0.198 10 false 4 0.74,0.667 1.115,0.844 0.375,0.177 10 false AM2 1.469,0.667 1.844,0.844 0.375,0.177 10 false ST2 4.052,1.365 4.365,1.563 0.313,0.198 10 false 2 2.927,2.458 3.24,2.656 0.313,0.198 10 false 4 4.052,2.458 4.365,2.656 0.313,0.198 10 false 5 2.958,1.365 3.271,1.563 0.313,0.198 10 false 1 2.219,2.823 2.635,3.021 0.417,0.198 10 false E92 2.625,1.833 2.938,2.031 0.313,0.198 10 false M7 2.229,3 4.885,3.24 2.656,0.24 10 false Park/Neutral Position Switch Assembly*2 2.615,2.01 5.521,2.344 2.906,0.333 10 false Clutch Start Switch Assembly*1 5.333,0.656 5.646,0.854 0.313,0.198 10 false 11 5.333,3.417 5.646,3.615 0.313,0.198 10 false 22 5.583,0.781 6.063,0.979 0.479,0.198 10 false NSW 5.583,3.552 6.063,3.75 0.479,0.198 10 false STA 2.677,5.958 4.281,6.188 1.604,0.229 10 false Starter Assembly 2.51,5.479 2.823,5.677 0.313,0.198 10 false F1 3.052,5.01 3.365,5.208 0.313,0.198 10 false E21 3.094,5.208 3.406,5.406 0.313,0.198 10 false ST 2.792,5.479 3.104,5.677 0.313,0.198 10 false B 3.219,4.813 3.531,5.01 0.313,0.198 10 false 1 2.531,5.281 2.844,5.479 0.313,0.198 10 false 1 3.76,4.583 4.073,4.781 0.313,0.198 10 false 1 3.792,3.813 4.104,4.01 0.313,0.198 10 false 2 3.031,3.792 3.344,3.99 0.313,0.198 10 false 5 3.031,4.583 3.344,4.781 0.313,0.198 10 false 3 3.938,4.219 4.594,4.427 0.656,0.208 10 false STARTER 1.969,3.688 2.625,3.896 0.656,0.208 10 false ST NO. 2 1.271,4.594 2.333,4.813 1.063,0.219 10 false FL MAIN 5.938,4.875 6.594,5.083 0.656,0.208 10 false N2 1.354,5.885 2.01,6.094 0.656,0.208 10 false Battery 0.458,2.156 2.063,2.385 1.604,0.229 10 false AM2 4.052,5.302 6.708,5.542 2.656,0.24 10 false *1: for Manual Transmission 4.052,5.552 6.708,5.792 2.656,0.24 10 false *2: for Automatic Transmission 3.135,1.385 3.448,1.583 0.313,0.198 10 false B 3.146,2.479 3.458,2.677 0.313,0.198 10 false B 3.813,2.49 4.125,2.688 0.313,0.198 10 false L 3.833,1.385 4.146,1.583 0.313,0.198 10 false L 5.927,5.052 6.583,5.26 0.656,0.208 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>PROBLEM SYMPTOMS TABLE).

·

If this DTC is output, inspect the starter assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

d.

Read the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more.


Result:
Result Proceed to
Driving at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more OFF A
ON B



A

B

2.INSPECT STARTER RELAY (CHECK FOR SHORT CIRCUIT)
2.INSPECT STARTER RELAY (CHECK FOR SHORT CIRCUIT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Remove the STARTER relay from the No. 1 engine room relay block and junction block assembly.


f.

According to the display on the GTS, read the Data List.

Result:
Result Proceed to
The Data List item "Starter SW" does not change from ON. A
The Data List item "Starter SW" changes from ON to OFF. B


HINT:
·

When the result of the above inspection is "The Data List item "Starter SW" does not change from ON", the STARTER relay is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STARTER RELAY)

B

14.REPLACE STARTER RELAY ASSEMBLY
3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STARTER RELAY)
A444442C04
0.073,0.063 0.417,0.281 0.344,0.219 10 false *1 2.219,0.271 2.563,0.49 0.344,0.219 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 STARTER Relay


HINT:

The purpose of this step is to check for STARTER relay terminal voltage under abnormal conditions.


a.

Remove the STARTER relay from the No. 1 engine room relay block and junction block assembly.


b.

Turn the ignition switch to ON.


c.

Measure the voltage between STARTER relay terminal 2 and body ground.

HINT:
·

Make a note of the measured voltage as it will be necessary for the inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the ignition switch ON and do not install the STARTER relay.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.

·

If any voltage was measured with the ignition switch ON, one of the following malfunctions is suspected:

-

Short to +B in the circuit of a connected ECU or the switch.

-

Short to +B in the wire harness.





Result:
Result Proceed to
NEXT
(for Automatic Transmission Models)
A
NEXT
(for Manual Transmission Models)
B



A

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)

B

9.INSPECT CLUTCH START SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
A444442C04
0.073,0.063 0.417,0.281 0.344,0.219 10 false *1 2.219,0.271 2.563,0.49 0.344,0.219 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 STARTER Relay


a.

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage between STARTER relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between STARTER relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between STARTER relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the park/neutral position switch assembly is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

5.INSPECT ECM (CHECK FOR SHORT CIRCUIT)

B

8.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
5.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
A444442C04
0.073,0.063 0.417,0.281 0.344,0.219 10 false *1 2.219,0.271 2.563,0.49 0.344,0.219 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 STARTER Relay


a.

Disconnect the ECM connector.


b.

Measure the voltage between STARTER relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between STARTER relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between STARTER relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the ECM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

B

7.REPLACE ECM
6.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (STA signal circuit).


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER DTC OUTPUT RECURS
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER DTC OUTPUT RECURS
8.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Replace the park/neutral position switch assembly.

Click hereDrivetrain>AC60E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER DTC OUTPUT RECURS
9.INSPECT CLUTCH START SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
A444442C04
0.073,0.063 0.417,0.281 0.344,0.219 10 false *1 2.219,0.271 2.563,0.49 0.344,0.219 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 STARTER Relay


a.

Disconnect the clutch start switch assembly connector.


b.

Measure the voltage between STARTER relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between STARTER relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between STARTER relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the clutch start switch assembly is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

10.INSPECT ECM (CHECK FOR SHORT CIRCUIT)

B

13.REPLACE CLUTCH START SWITCH ASSEMBLY
10.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
A444442C04
0.073,0.063 0.417,0.281 0.344,0.219 10 false *1 2.219,0.271 2.563,0.49 0.344,0.219 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 STARTER Relay


a.

Disconnect the ECM connector.


b.

Measure the voltage between STARTER relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between STARTER relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between STARTER relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the ECM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

11.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

B

12.REPLACE ECM
11.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (STA signal circuit).


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER DTC OUTPUT RECURS
12.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER DTC OUTPUT RECURS
13.REPLACE CLUTCH START SWITCH ASSEMBLY
a.

Replace the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER DTC OUTPUT RECURS
14.REPLACE STARTER RELAY ASSEMBLY
a.

Replace the STARTER relay.


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER DTC OUTPUT RECURS
15.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle for 20 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END