Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR) › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0395991 ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR) D

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR)  INITIALIZATION  


INITIALIZATION PROCEDURE FOR DIESEL THROTTLE BODY ASSEMBLY, ELECTRIC EGR CONTROL VALVE ASSEMBLY AND TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR


HINT:

When the diesel throttle body assembly, electric EGR control valve assembly or turbocharger nozzle vane control actuator is replaced, perform initialization.


a.

Turn the engine switch on (IG).

NOTICE:

Do not start the engine.



b.

Turn the engine switch off and wait for 30 seconds or more.


c.

Turn the engine switch on (IG) and wait for 10 seconds or more.



CATALYST DETERIORATION LEARNING VALUE AND DPF DEPOSITION VALUE CLEAR FUNCTION


HINT:

When the exhaust manifold converter sub-assembly (DPF catalyst) is replaced, the catalyst deterioration learning value and DPF deposition value stored in the ECM must be cleared.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the menu options in this order: Powertrain / Engine and Transmission / Utility / Catalyst Deterioration Leaning Value Clear.

Powertrain > Engine and Transmission > Utility
Tester Display
Catalyst Deterioration Learning Value Clear
50005 456 4568

e.

Press "Next".


f.

Press "Exit".


g.

Enter the menu options in this order: Powertrain / Engine and Transmission / Utility / DPF Deposition Value Clear.

Powertrain > Engine and Transmission > Utility
Tester Display
DPF Deposition Value Clear
50005 456 4574

h.

Press "Next".


i.

Press "Exit".



CRANK TIME COMPENSATION LEARNING VALUE CLEAR FUNCTION


·

This procedure uses the GTS to perform "Crank Time Compensation Learning Value Clear".

·

When replacing the timing rotor (engine assembly), perform "Crank Time Compensation Learning Value Clear".


HINT:
·
A204035

If an error occurs during compensation reset, check the vehicle condition, and then perform compensation reset again.

·

A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).

NOTICE:

Do not start the engine.



c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and Transmission / Utility / Crank Time Compensation Learning Value Clear.

Powertrain > Engine and Transmission > Utility
Tester Display
Crank Time Compensation Learning Value Clear
50005 456 4571

e.
A280989

When the first screen is displayed, check the vehicle condition and push "Next".


f.
A280984

When the screen indicating reset completion is displayed, push "Exit".



A/F SENSOR LEARNING VALUE CLEAR FUNCTION


·

This procedure uses the GTS to perform "A/F Sensor Learning Value Clear".

·

When replacing the No. 1 nitrogen oxides sensor, replace the sensor and then perform "A/F Sensor Learning Value Clear".

HINT:

The No. 1 nitrogen oxides sensor has an air fuel ratio sensor function. Therefore, perform "A/F Sensor Learning Value Clear" after replacing the No. 1 nitrogen oxides sensor.



HINT:
·
A204038

If an error occurs during compensation reset, check the vehicle condition, and then perform compensation reset again.

·

A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).

NOTICE:

Do not start the engine.



c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and Transmission / Utility / A/F Sensor Learning Value Clear.

Powertrain > Engine and Transmission > Utility
Tester Display
A/F Sensor Learning Value Clear
50005 456 4572

e.
A295533

When the first screen is displayed, check the vehicle condition and press "Next".


f.
A295534

When the screen indicating reset completion is displayed, press "Exit".