Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR) › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0395991 ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR) U

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR)  TERMINALS OF ECM  


A340466E54
0.531,0.438 0.969,0.677 0.438,0.24 1.74,0.438 2.177,0.677 0.438,0.24 2.844,0.438 3.281,0.677 0.438,0.24 3.885,0.438 4.323,0.677 0.438,0.24 5,0.438 5.438,0.677 0.438,0.24 6.156,0.438 6.594,0.677 0.438,0.24 1.875,0.469 2.188,0.667 0.313,0.198 10 false E6 0.667,0.469 0.979,0.667 0.313,0.198 10 false E5 2.979,0.469 3.292,0.667 0.313,0.198 10 false E7 4.021,0.479 4.333,0.677 0.313,0.198 10 false E8 5.135,0.469 5.448,0.667 0.313,0.198 10 false N2 6.292,0.469 6.604,0.667 0.313,0.198 10 false A2

HINT:

Each ECM terminal's standard voltage is shown in the table below.

In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".

Use the illustration above as a reference for the ECM terminals.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N2-1 (BATT) - A2-5 (E1) L - W-B Battery (for measuring the battery voltage and for the ECM memory) Always 11 to 14 V
A2-18 (IGSW) - A2-5 (E1) SB - W-B Engine switch Engine switch on (IG) 11 to 14 V
N2-4 (+B) - A2-5 (E1) B - W-B Power source of ECM Engine switch on (IG) 11 to 14 V
N2-3 (+B2) - A2-5 (E1) B - W-B Power source of ECM Engine switch on (IG) 11 to 14 V
N2-2 (+B3) - A2-5 (E1) B - W-B Power source of ECM Engine switch on (IG) 11 to 14 V
N2-14 (MREL) - A2-5 (E1) GR - W-B EFI MAIN relay operation signal Engine switch on (IG) 0 to 1.5 V
10 seconds elapsed after engine switch off 11 to 14 V
N2-6 (+BD1) - A2-5 (E1) W - W-B EDU relay operation signal Engine switch on (IG) 11 to 14 V
N2-5 (+BD2) - A2-5 (E1) B - W-B EDU relay operation signal Engine switch on (IG) 11 to 14 V
N2-19 (GREL) - A2-5 (E1) R - W-B GLOW relay Cranking 0 to 1.5 V
Idling (10 seconds or more after engine start) 11 to 14 V
N2-11 (NSW) - A2-5 (E1) B - W-B Park/neutral position switch assembly signal Engine switch on (IG), shift lever not in P or N 11 to 14 V
Engine switch on (IG), shift lever in P or N Below 1.0 V
A2-29 (VCPA) - A2-22 (EPA) V - LG Power source of accelerator pedal position sensor (for VPA) Engine switch on (IG) 4.5 to 5.5 V
A2-30 (VCP2) - A2-25 (EPA2) L - P Power source of accelerator pedal position sensor (for VPA2) Engine switch on (IG) 4.5 to 5.5 V
A2-28 (VPA) - A2-22 (EPA) Y - LG Accelerator pedal position sensor signal (for engine control) Engine switch on (IG), accelerator pedal fully released 0.5 to 1.1 V
Accelerator pedal position sensor signal (for engine control) Engine switch on (IG), accelerator pedal fully depressed 3.0 to 4.6 V
A2-31 (VPA2) - A2-25 (EPA2) GR - P Accelerator pedal position sensor signal (for sensor malfunction detection) Engine switch on (IG), accelerator pedal fully released 0.9 to 2.3 V
Accelerator pedal position sensor signal (for sensor malfunction detection) Engine switch on (IG), accelerator pedal fully depressed 3.4 to 5.0 V
E6-30 (VCVG) - E6-29 (EVG) G - L Power source of mass air flow meter sub-assembly (for VG) Engine switch on (IG) 4.8 to 5.2 V
E6-31 (VG) - E6-29 (EVG) B - L Mass air flow meter sub-assembly signal Engine switch on (IG) Pulse generation
(See waveform 1)
E6-28 (THA) - E6-29 (EVG) R - L Intake air temperature sensor (built into mass air flow meter sub-assembly) Idling, intake air temperature at 20°C (68°F) 0.5 to 3.4 V
E5-26 (THIA) - E5-27 (E2) G - BR Intake air temperature sensor (turbo) Idling, intake air temperature at 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
E5-34 (THW) - E5-27 (E2) R - BR Engine coolant temperature sensor Idling, engine coolant temperature at 80°C (176°F) 0.2 to 1.0 V
N2-22 (STA) - A2-5 (E1) B - W-B Starter signal Cranking 6.0 V or higher
E5-6 (#1D+) - E5-7 (#1D-) W - B No. 1 injector assembly signal Idling Pulse generation
(See waveform 2)
E5-1 (#2D+) - E5-2 (#2D-) R - W No. 2 injector assembly signal
E6-7 (#3D+) - E6-6 (#3D-) Y - L No. 3 injector assembly signal
E5-5 (#4D+) - E5-4 (#4D-) G - R No. 4 injector assembly signal
E8-17 (VCG) - E8-18 (G2-) B - W Power source of camshaft position sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
E8-27 (G2+) - E8-18 (G2-) R - W Camshaft position sensor signal Idling Pulse generation
(See waveform 3)
E8-20 (VCNE) - E8-19 (NE-) W - R Power source of crankshaft position sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
E8-28 (NE+) - E8-19 (NE-) Y - R Crankshaft position sensor signal Idling Pulse generation
(See waveform 4)
A2-13 (STP) - A2-5 (E1) V - W-B Stop light switch assembly signal Engine switch on (IG), brake pedal depressed 7.5 to 14 V
Engine switch on (IG), brake pedal released 0 to 1.5 V
A2-12 (ST1-) - A2-5 (E1) B - W-B Stop light switch assembly signal
(opposite to STP)
Engine switch on (IG), brake pedal depressed 0 to 1.5 V
Engine switch on (IG), brake pedal released 7.5 to 14 V
N2-10 (SPD) - A2-5 (E1) V - W-B Speed signal from combination meter assembly Engine switch on (IG), slowly wheel rotated Pulse generation
(See waveform 5)
E5-28 (VCPM) - E5-19 (EPIM) R - BR Power source of manifold absolute pressure sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
E5-18 (PIM) - E5-19 (EPIM) L - BR Manifold absolute pressure sensor Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied 0.1 to 0.7 V
Same as atmospheric pressure 0.8 to 1.5 V
Positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) applied 1.6 to 2.3 V
E7-28 (VCM) - E7-19 (E2M) B - R Power source of fuel pressure sensor (for PCR1) Engine switch on (IG) 4.5 to 5.5 V
E7-18 (PCR1) - E7-19 (E2M) W - R Fuel pressure sensor signal (main) Idling 1.8 to 2.1 V
E8-22 (VCS) - E8-21 (E2S) L - P Power source of fuel pressure sensor (for PCR2) Engine switch on (IG) 4.5 to 5.5 V
E8-23 (PCR2) - E8-21 (E2S) G - P Fuel pressure sensor signal (sub) Idling 1.2 to 1.5 V
E6-3 (PCV+) - E6-4 (PCV-) G - R Pre-stroke control valve operation signal Idling Pulse generation
(See waveform 6)
E6-2 (PRV+) - E6-1 (PRV-) V - P Pressure discharge valve signal Engine switch turned off after idling Pulse generation
E7-1 (VNM+) - A2-5 (E1) L - W-B Variable vane DC motor signal (turbocharger nozzle vane control actuator) Idling Pulse generation
E7-2 (VNM-) - A2-5 (E1) W - W-B Variable vane DC motor signal (turbocharger nozzle vane control actuator) Idling Pulse generation
E7-30 (VNVC) - E7-22 (VNE2) R - L Power source of nozzle vane position sensor (turbocharger nozzle vane control actuator) Engine switch on (IG) 4.5 to 5.5 V
E7-23 (VNA) - E7-22 (VNE2) P - L Nozzle vane position sensor signal (turbocharger nozzle vane control actuator) Engine switch on (IG) 2.3 to 2.7 V
E7-29 (VCVL) - E7-20 (EVLU) Y - L Power source of throttle position sensor Engine switch on (IG) 4.5 to 5.5 V
E7-21 (VLU) - E7-20 (EVLU) W- L Throttle position sensor signal Engine switch on (IG), throttle valve fully opened 3.6 to 4.2 V
Engine switch on (IG), throttle valve fully closed 0.4 to 1.0 V
E7-5 (M+) - A2-1 (ME01) G - W-B Diesel throttle duty signal Engine warmed up, racing engine Pulse generation
E7-4 (M-) - A2-1 (ME01) R - W-B Diesel throttle duty signal Engine warmed up, racing engine Pulse generation
E7-31 (VCEG) - E7-24 (EEGL) R - W Power source of EGR valve position sensor Engine switch on (IG) 4.5 to 5.5 V
E7-25 (EGRA) - E7-24 (EEGL) G - W EGR valve position sensor Engine switch on (IG) 0.6 to 1.4 V
E7-6 (EGM+) - A2-5 (E1) B - W-B EGR valve duty signal Engine warmed up, idling Pulse generation
E7-7 (EGM-) - A2-5 (E1) W - W-B EGR valve duty signal Engine warmed up, idling Pulse generation
E5-16 (ECBV) - A2-5 (E1) L - W-B Vacuum switching valve assembly (for EGR Bypass Valve) Vacuum switching valve assembly (for EGR Bypass Valve) on 0 to 1.5 V
Vacuum switching valve assembly (for EGR Bypass Valve) off 11 to 14 V
E8-12 (ECB2) - A2-5 (E1) W - W-B Vacuum switching valve assembly (for No. 2 EGR Bypass Valve) Vacuum switching valve assembly (for No. 2 EGR Bypass Valve) on 0 to 1.5 V
Vacuum switching valve assembly (for No. 2 EGR Bypass Valve) off 11 to 14 V
E8-1 (FIV+) - E7-3 (FIV-) B - R Exhaust fuel addition injector assembly signal Exhaust fuel addition injector operating Pulse generation
E7-32 (VCPX) - E7-26 (EPEX) R - BR Power source for differential pressure sensor Engine switch on (IG) 4.5 to 5.5 V
E7-27 (PEX) - E7-26 (EPEX) L - BR Differential pressure sensor Engine switch on (IG) 0.4 to 4.8 V
E5-22 (THGO) - E5-27 (E2) P - W-B No. 5 exhaust gas temperature sensor (EGR gas temperature sensor) Engine warmed up, idling 0.2 to 4.95 V
E5-23 (THTO) - E5-27 (E2) G - BR Exhaust gas temperature sensor Engine warmed up, idling 0.2 to 4.95 V
E5-25 (THCI) - E5-27 (E2) L - BR No. 2 exhaust gas temperature sensor Engine warmed up, idling 0.2 to 4.95 V
E5-33 (THCO) - E5-27 (E2) B - BR No. 3 exhaust gas temperature sensor Engine warmed up, idling 0.2 to 4.95 V
E5-24 (THSO) - E5-27 (E2) B - BR No. 4 exhaust gas temperature sensor Engine warmed up, idling 0.2 to 4.95 V
E5-10 (SCV) - A2-4 (E01) LG - W-B Vacuum switching valve assembly (for Swirl Control Valve) Idling 0 to 1.5 V
Engine speed 2600 rpm or more 11 to 14 V
N2-23 (NEO) - A2-5 (E1) W - W-B Crankshaft position sensor signal sent to certification ECU (smart key ECU assembly) Engine warmed up, idling Pulse generation
(See waveform 7)
N2-28 (CANL) - A2-5 (E1) W - W-B CAN communication line Engine switch on (IG) Pulse generation
(See waveform 8)
N2-17 (CANH) - A2-5 (E1) G - W-B CAN communication line Engine switch on (IG) Pulse generation
(See waveform 9)
N2-35 (CAND) - A2-5 (E1) W - W-B CAN communication line Engine switch on (IG) Pulse generation
(See waveform 8)
N2-27 (CANU) - A2-5 (E1) LG - W-B CAN communication line Engine switch on (IG) Pulse generation
(See waveform 9)
E8-7 (LIN) - A2-5 (E1) P - W-B LIN communication line Engine switch on (IG) Pulse generation
(See waveform 10)
A2-4 (E01) - Body ground W-B - Body ground Ground circuit of ECM Always Below 1 Ω
A2-3 (E02) - Body ground W-B - Body ground Ground circuit of ECM Always Below 1 Ω
A2-5 (E1) - Body ground W-B - Body ground Ground circuit of ECM Always Below 1 Ω
A2-1 (ME01) - Body ground W-B - Body ground Ground circuit of ECM Always Below 1 Ω
A2-8 (EC) - Body ground BR - Body ground Ground circuit of ECM Always Below 1 Ω
A2-7 (E1D1) - Body ground W-B - Body ground Ground circuit of ECM Always Below 1 Ω
A2-6 (E1D2) - Body ground W-B - Body ground Ground circuit of ECM Always Below 1 Ω
A2-2 (E04) - Body ground W-B - Body ground Ground circuit of ECM Always Below 1 Ω

WAVEFORM 1


A337204E04
0.156,1.417 0.615,1.615 0.458,0.198 10 false GND 1.333,1.969 2.583,2.156 1.25,0.188 10 false 100 μsec./DIV. 2.76,0.073 3.406,0.333 0.646,0.26 10 false 1 V/DIV.

Mass Air Flow Meter Sub-assembly Signal
ECM Terminal Name Between VG and EVG
Tester Range 1 V/DIV., 100 μsec./DIV.
Condition Engine switch on (IG)


WAVEFORM 2


A346498E02
1.094,1.917 1.958,2.115 0.865,0.198 10 false 1 msec./DIV. 2.781,0.146 3.396,0.344 0.615,0.198 10 false 10 V/DIV. 2.969,1.188 3.344,1.385 0.375,0.198 10 false GND

No. 1 (to No. 4) Injector Assembly Signal
ECM Terminal Name Between #1D+ and #1D-
Between #2D+ and #2D-
Between #3D+ and #3D-
Between #4D+ and #4D-
Tester Range 10 V/DIV., 1 msec./DIV.
Condition Idling after engine warmed

HINT:

The waveform varies depending on the injector injection.



WAVEFORM 3


A340470E01
2.854,0.156 3.406,0.344 0.552,0.188 10 false 5 V/DIV. 3.042,1.427 3.406,1.646 0.365,0.219 10 false GND 1.094,1.854 2.052,2.031 0.958,0.177 10 false 20 msec./DIV.

Camshaft Position Sensor Signal
ECM Terminal Name Between G2+ and G2-
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Idling after engine warmed

HINT:

The waveform varies depending on the engine speed.



WAVEFORM 4


A340468E01
2.833,0.135 3.396,0.354 0.563,0.219 10 false 2 V/DIV. 1.24,1.833 2.229,2.042 0.99,0.208 10 false 10 msec./DIV. 3.073,1.375 3.417,1.635 0.344,0.26 10 false GND

Crankshaft Position Sensor Signal
ECM Terminal Name Between NE+ and NE-
Tester Range 2 V/DIV., 10 msec./DIV.
Condition Idling after engine warmed

HINT:

The wavelength becomes shorter as the engine speed.



WAVEFORM 5


A303294E02
2.75,0.125 3.365,0.333 0.615,0.208 10 false 5 V/DIV. 2.927,1.115 3.302,1.333 0.375,0.219 10 false GND 1.521,1.885 2.521,2.125 1,0.24 10 false 10 msec./DIV.

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 5 V/DIV., 10 msec./DIV.
Condition Driving at vehicle speed of 40 km/h (25 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 6


A346499E01
2.76,0.073 3.385,0.292 0.625,0.219 10 false 10 V/DIV. 1.104,1.865 2.083,2.042 0.979,0.177 10 false 20 msec./DIV. 3.031,1.01 3.365,1.208 0.333,0.198 10 false GND

Pre-stroke Control Valve Signal
ECM Terminal Name Between PCV+ and PCV-
Tester Range 10 V/DIV., 20 msec./DIV.
Condition Idling after engine warmed

HINT:

The waveform varies depending on pre-stroke control valve operation.



WAVEFORM 7


A287796E13
2.604,1.625 3.063,1.823 0.458,0.198 10 false GND 0.063,0.063 0.781,0.292 0.719,0.229 10 false 1 V/DIV. 1.167,1.927 2.156,2.135 0.99,0.208 10 false 2 msec./DIV.

Engine Speed Signal
ECM Terminal Name Between NEO and E1
Tester Range 1 V/DIV., 2 msec./DIV.
Condition Idling after engine warmed


WAVEFORM 8


A303296E01
2.802,0.156 3.396,0.385 0.594,0.229 10 false 1 V/DIV. 2.99,1.229 3.333,1.469 0.344,0.24 10 false GND 1.615,1.76 2.719,1.969 1.104,0.208 10 false 10 msec./DIV.

CAN Communication Signal
ECM Terminal Name Between CANL and E1
Between CAND and E1
Tester Range 1 V/DIV., 10 msec./DIV.
Condition Engine stopped, engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 9


A303295E01
2.771,0.167 3.385,0.375 0.615,0.208 10 false 1 V/DIV. 2.958,1.25 3.344,1.5 0.385,0.25 10 false GND 1.573,1.781 2.625,2.031 1.052,0.25 10 false 10 msec./DIV.

CAN Communication Signal
ECM Terminal Name Between CANH and E1
Between CANU and E1
Tester Range 1 V/DIV., 10 msec./DIV.
Condition Engine stopped, engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 10


A349005E01
1.177,2.49 2.188,2.688 1.01,0.198 10 false 10 msec./DIV. 2.917,1.896 3.271,2.104 0.354,0.208 10 false GND 2.698,0.792 3.292,0.99 0.594,0.198 10 false 2 V/DIV.

LIN Communication Signal
ECM Terminal Name Between LIN and E1
Tester Range 2 V/DIV., 10 msec./DIV.
Condition Engine stopped, engine switch on (IG)

HINT:

The waveform varies depending on the LIN communication signal.