This DTC is stored when a microphone signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1572 | Microphone Error | Current at terminal MCVD exceeds the malfunction threshold for 10 seconds or more while the ignition switch is ON. | ·
Telephone transceiver assembly ·
Communication telematics box ·
Map light assembly ·
Mayday wire* ·
Harness or connector |
*: Standard Roof
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>REGISTRATION
When replacing the telephone transceiver assembly, make sure to replace it with a new one.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait for 20 seconds.
Turn the GTS on.
Check for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
No DTCs are output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (High roof) | B |
| NG (Standard roof) | C |
A
Click here
B
C
| *a | Component with harness connected
(Telephone Transceiver Assembly) |
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N74-31 (MICV) - Body ground | Ignition switch ACC | 4 to 6 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N74-35 (MCI-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N74 telephone transceiver assembly connector.
Disconnect the a19 map light assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N74-14 (MCMD) - a19-6 (MCMD) | Always | Below 1 Ω |
| N74-20 (SP+) - a19-4 (SP+) | Always | Below 1 Ω |
| N74-21 (SP-) - a19-15 (SP-) | Always | Below 1 Ω |
| N74-31 (MICV) - a19-1 (MICV) | Always | Below 1 Ω |
| N74-33 (MCVD) - a19-14 (MIC1) | Always | Below 1 Ω |
| N74-34 (MCI+) - a19-13 (MIC2) | Always | Below 1 Ω |
| N74-35 (MCI-) - a19-2 (MCI-) | Always | Below 1 Ω |
| N74-14 (MCMD) or a19-6 (MCMD) - Body ground | Always | 10 kΩ or higher |
| N74-20 (SP+) or a19-4 (SP+) - Body ground | Always | 10 kΩ or higher |
| N74-21 (SP-) or a19-15 (SP-) - Body ground | Always | 10 kΩ or higher |
| N74-31 (MICV) or a19-1 (MICV) - Body ground | Always | 10 kΩ or higher |
| N74-33 (MCVD) or a19-14 (MIC1) - Body ground | Always | 10 kΩ or higher |
| N74-34 (MCI+) or a19-13 (MIC2) - Body ground | Always | 10 kΩ or higher |
| N74-35 (MCI-) or a19-2 (MCI-) - Body ground | Always | 10 kΩ or higher |
| N74-32 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Remove the communication telematics box.
Click hereAudio / Visual / Telematics>TELEMATICS>COMMUNICATION TELEMATICS BOX>REMOVAL
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a19-1 (MICV) - P-5 (MICV) | Always | Below 1 Ω |
| a19-2 (MCI-) - P-4 (MCI-) | Always | Below 1 Ω |
| a19-4 (SP+) - P-3 (SP+) | Always | Below 1 Ω |
| a19-6 (MCMD) - P-1 (MCMD) | Always | Below 1 Ω |
| a19-13 (MIC2) - P-7 (MIC2+) | Always | Below 1 Ω |
| a19-14 (MIC1) - P-2 (MIC1+) | Always | Below 1 Ω |
| a19-15 (SP-) - P-8 (SP-) | Always | Below 1 Ω |
| a19-1 (MICV) - a19-15 (SP-) | Always | 10 kΩ or higher |
| a19-2 (MCI-) - a19-15 (SP-) | Always | 10 kΩ or higher |
| a19-4 (SP+) - a19-15 (SP-) | Always | 10 kΩ or higher |
| a19-6 (MCMD) - a19-15 (SP-) | Always | 10 kΩ or higher |
| a19-13 (MIC2) - a19-15 (SP-) | Always | 10 kΩ or higher |
| a19-14 (MIC1) - a19-15 (SP-) | Always | 10 kΩ or higher |
| a19-1 (MICV) - a19-14 (MIC1) | Always | 10 kΩ or higher |
| a19-2 (MCI-) - a19-14 (MIC1) | Always | 10 kΩ or higher |
| a19-4 (SP+) - a19-14 (MIC1) | Always | 10 kΩ or higher |
| a19-6 (MCMD) - a19-14 (MIC1) | Always | 10 kΩ or higher |
| a19-13 (MIC2) - a19-14 (MIC1) | Always | 10 kΩ or higher |
| a19-1 (MICV) - a19-13 (MIC2) | Always | 10 kΩ or higher |
| a19-2 (MCI-) - a19-13 (MIC2) | Always | 10 kΩ or higher |
| a19-4 (SP+) - a19-13 (MIC2) | Always | 10 kΩ or higher |
| a19-6 (MCMD) - a19-13 (MIC2) | Always | 10 kΩ or higher |
| a19-1 (MICV) - a19-6 (MCMD) | Always | 10 kΩ or higher |
| a19-2 (MCI-) - a19-6 (MCMD) | Always | 10 kΩ or higher |
| a19-4 (SP+) - a19-6 (MCMD) | Always | 10 kΩ or higher |
| a19-1 (MICV) - a19-4 (SP+) | Always | 10 kΩ or higher |
| a19-2 (MCI-) - a19-4 (SP+) | Always | 10 kΩ or higher |
| a19-1 (MICV) - a19-2 (MCI-) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the communication telematics box with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>COMMUNICATION TELEMATICS BOX>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Component with harness connected
(Telephone Transceiver Assembly) |
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N74-31 (MICV) - Body ground | Ignition switch ACC | 4 to 6 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N74-35 (MCI-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N74 telephone transceiver assembly connector.
Disconnect the a38 mayday wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N74-14 (MCMD) - a38-1 (MCMD) | Always | Below 1 Ω |
| N74-20 (SP+) - a38-3 (SP+) | Always | Below 1 Ω |
| N74-21 (SP-) - a38-9 (SP-) | Always | Below 1 Ω |
| N74-31 (MICV) - a38-6 (MICV) | Always | Below 1 Ω |
| N74-33 (MCVD) - a38-10 (MIC1) | Always | Below 1 Ω |
| N74-34 (MCI+) - a38-11 (MIC2) | Always | Below 1 Ω |
| N74-35 (MCI-) - a38-5 (MCI-) | Always | Below 1 Ω |
| N74-14 (MCMD) or a38-1 (MCMD) - Body ground | Always | 10 kΩ or higher |
| N74-20 (SP+) or a38-3 (SP+) - Body ground | Always | 10 kΩ or higher |
| N74-21 (SP-) or a38-9 (SP-) - Body ground | Always | 10 kΩ or higher |
| N74-31 (MICV) or a38-6 (MICV) - Body ground | Always | 10 kΩ or higher |
| N74-33 (MCVD) or a38-10 (MIC1) - Body ground | Always | 10 kΩ or higher |
| N74-34 (MCI+) or a38-11 (MIC2) - Body ground | Always | 10 kΩ or higher |
| N74-35 (MCI-) or a38-5 (MCI-) - Body ground | Always | 10 kΩ or higher |
| N74-32 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the a38 wire harness connector.
Disconnect the P communication telematics box connector.
| *a | Component without harness connected
(Wire Harness) |
| *b | Component without harness connected
(Communication Telematics Box) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a38-1 (MCMD) - P-1 (MCMD) | Always | Below 1 Ω |
| a38-3 (SP+) - P-3 (SP+) | Always | Below 1 Ω |
| a38-9 (SP-) - P-8 (SP-) | Always | Below 1 Ω |
| a38-6 (MICV) - P-5 (MICV) | Always | Below 1 Ω |
| a38-10 (MIC1) - P-2 (MIC1+) | Always | Below 1 Ω |
| a38-11 (MIC2) - P-7 (MIC2+) | Always | Below 1 Ω |
| a38-5 (MCI-) - P-4 (MCI-) | Always | Below 1 Ω |
| a38-1 (MCMD) or P-1 (MCMD) - Body ground | Always | 10 kΩ or higher |
| a38-3 (SP+) or P-3 (SP+) - Body ground | Always | 10 kΩ or higher |
| a38-9 (SP-) or P-8 (SP-) - Body ground | Always | 10 kΩ or higher |
| a38-6 (MICV) or P-5 (MICV) - Body ground | Always | 10 kΩ or higher |
| a38-10 (MIC1) or P-2 (MIC1+) - Body ground | Always | 10 kΩ or higher |
| a38-11 (MIC2) or P-7 (MIC2+) - Body ground | Always | 10 kΩ or higher |
| a38-5 (MCI-) or P-4 (MCI-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the communication telematics box with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>COMMUNICATION TELEMATICS BOX>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT