This DTC is stored when GNSS satellite signals is not received for 30 km.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1583 | GPS Signal Unreceived | GNSS signals are not received for 30 km. | ·
Telephone transceiver assembly ·
Navigation Antenna Assembly ·
Antenna cord sub-assembly ·
Antenna divider* ·
Harness or connector |
*: Standard Roof
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>REGISTRATION
When replacing the telephone transceiver assembly, make sure to replace it with a new one.
If the vehicle is outside the communication service area, move the vehicle into a communication service area, wait for a while and perform the operation again.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait for 20 seconds.
Turn the GTS on.
Check for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.
| Result | Proceed to |
|---|---|
| Optional components are not installed | A |
| Optional components are installed | B |
Do not remove optional components without the permission of the customer.
A
B
Clear the DTCs.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
Recheck for DTCs and check if the same DTC is output again.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| No DTCs are output. | A |
| DTC B1583 is output.(High roof) | B |
| DTC B1583 is output.(Standard roof) | C |
A
B
C
Remove the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>REMOVAL
Inspect the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Navigation Antenna Assembly) |
| *b | Front view of wire harness connector
(to Wire Harness) |
Disconnect the antenna cord sub-assembly from the navigation antenna assembly connector.
Disconnect the antenna cord sub-assembly from the wire harness connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-3 - N141-1 (GPS) | Always | Below 1 Ω |
| B-3a - N141-1a | Always | Below 1 Ω |
| B-3 or N141-1 (GPS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel Side)>REMOVAL
| *a | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Telephone Transceiver Assembly) |
Disconnect the antenna cord sub-assembly connector.
Disconnect the telephone transceiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N141-1 (GPS) - N140-1 (ANT2) | Always | Below 1 Ω |
| N141-1a - N140-1a | Always | Below 1 Ω |
| N141-1 (GPS) or N140-1 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Remove the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>REMOVAL
Inspect the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Navigation Antenna Assembly) |
| *b | Front view of wire harness connector
(to Antenna Divider) |
| *c | Front view of wire harness connector
(to Wire Harness) |
Disconnect the antenna cord sub-assembly from the navigation antenna assembly connector.
Disconnect the antenna cord sub-assembly from the antenna divider connector.
Disconnect the antenna cord sub-assembly from the wire harness connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-3 - C-6 | Always | Below 1 Ω |
| C-5 - N141-1(GPS) | Always | Below 1 Ω |
| B-3a - C-6a | Always | Below 1 Ω |
| C-5a - N141-1a | Always | Below 1 Ω |
| B-3 or C-6 - Body ground | Always | 10 kΩ or higher |
| C-5 or N141-1 (GPS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel Side)>REMOVAL
| *a | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Telephone Transceiver Assembly) |
Disconnect the antenna cord sub-assembly connector.
Disconnect the telephone transceiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N141-1 (GPS) - N140-1 (ANT2) | Always | Below 1 Ω |
| N141-1a - N140-1a | Always | Below 1 Ω |
| N141-1 (GPS) or N140-1 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Antenna Divider) |
Remove the antenna divider.
Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 - 6 | Always | Below 1 Ω |
| 5a - 6a | Always | Below 1 Ω |
| 5 - 5a | Always | 10 kΩ or higher |
| 6 - 6a | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT