Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for ERA-GLONASS) › 2019.06–2021.07
RM35X0E _56 Audio / Visual / Telematics _078380 TELEMATICS _0385046 TELEMATICS SYSTEM(for ERA-GLONASS) C

TELEMATICS  TELEMATICS SYSTEM(for ERA-GLONASS)  B15C0  Short in GPS Antenna  B15C1  Open in GPS Antenna  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 Short in GPS Antenna Current to the navigation antenna assembly is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON.
(Short circuit)
·

Telephone transceiver assembly

·

Navigation antenna assembly

·

Antenna cord sub-assembly

·

Antenna divider*

·

Harness or connector


B15C1 Open in GPS Antenna Current for navigation antenna assembly is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON.
(Open circuit)
·

Telephone transceiver assembly

·

Navigation antenna assembly

·

Antenna cord sub-assembly

·

Antenna divider*

·

Harness or connector



*: Standard Roof

WIRING DIAGRAM

High Roof
E409654E04
0.875,1.833 2.115,2.635 1.24,0.802 10 false Navigation Antenna Assembly 3.01,1.823 4.219,2.542 1.208,0.719 10 false Antenna Cord Sub-assembly 2.573,0.833 4.083,1.521 1.51,0.688 10 false B 2.594,1.448 4.104,2.135 1.51,0.688 10 false B 2.573,0.646 4.083,1.333 1.51,0.688 10 false 3 2.563,1.24 4.073,1.927 1.51,0.688 10 false 3a 4.479,0.844 5.99,1.531 1.51,0.688 10 false N141 4.469,1.427 5.979,2.115 1.51,0.688 10 false N141 4.552,1.24 6.063,1.927 1.51,0.688 10 false 1a 4.552,0.625 6.063,1.313 1.51,0.688 10 false 1 5.5,2.25 5.958,2.427 0.458,0.177 10 false N140 5.396,1.323 6.906,2.01 1.51,0.688 10 false 1a 5.448,0.729 6.958,1.417 1.51,0.688 10 false 1 5.51,2.427 6.906,2.792 1.396,0.365 10 false Telephone Transceiver Assembly 5.729,0.854 7.104,1.615 1.375,0.76 10 false ANT2 4,0.854 5.375,1.615 1.375,0.76 10 false GPS

Standard Roof
E418055E01
4.531,3.469 5.365,3.813 0.833,0.344 10 false N141 2.635,0.479 2.792,0.677 0.156,0.198 10 false C 2.635,0.927 2.792,1.125 0.156,0.198 10 false C 2.656,1.333 2.813,1.531 0.156,0.198 10 false C 2.646,1.792 2.802,1.99 0.156,0.198 10 false C 2.635,3.188 2.792,3.385 0.156,0.198 10 false B 2.625,3.625 2.781,3.823 0.156,0.198 10 false B 4.521,3.01 5.135,3.323 0.615,0.313 10 false N141 5.75,3.021 6.365,3.333 0.615,0.313 10 false ANT2 4.625,2.823 5.24,3.135 0.615,0.313 10 false 1 4.615,3.26 5.229,3.573 0.615,0.313 10 false 1a 2.615,3.406 3.229,3.719 0.615,0.313 10 false 3a 2.646,2.958 3.26,3.271 0.615,0.313 10 false 3 2.635,0.302 3.25,0.615 0.615,0.313 10 false 6 2.615,0.729 3.229,1.042 0.615,0.313 10 false 6a 2.656,1.146 3.271,1.458 0.615,0.313 10 false 5 2.615,1.583 3.229,1.896 0.615,0.313 10 false 5a 1.427,2.135 3.719,2.333 2.292,0.198 10 false Antenna Divider 5.688,4.208 7.125,4.771 1.438,0.563 10 false Telephone Transceiver Assembly 0.625,3.938 2.917,4.135 2.292,0.198 10 false Navigation Antenna Assembly 2.927,3.958 5.219,4.156 2.292,0.198 10 false Antenna Cord Sub-assembly 5.646,4.021 7.083,4.583 1.438,0.563 10 false N140 5.521,2.885 6.135,3.198 0.615,0.313 10 false 1 5.469,3.354 6.083,3.667 0.615,0.313 10 false 1a 4.094,3.021 4.708,3.333 0.615,0.313 10 false GPS

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>REGISTRATION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Result Proceed to
OK A
NG (High roof) B
NG (Standard roof) C



A

B

2.INSPECT NAVIGATION ANTENNA ASSEMBLY

C

6.INSPECT NAVIGATION ANTENNA ASSEMBLY
2.INSPECT NAVIGATION ANTENNA ASSEMBLY


Result:
Proceed to
OK
NG



OK

3.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

3.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.
E409655C01
1.521,1.917 1.938,2.156 0.417,0.24 1.469,0.156 1.885,0.396 0.417,0.24 1.875,0.875 2.448,1.208 2.448,1.208 2.604,1.208 true 1.813,2.781 2.25,2.5 2.25,2.5 2.406,2.5 true 1.646,2.792 1.281,2.469 1.281,2.469 1.135,2.469 true 1.573,1.948 2.073,2.292 0.5,0.344 10 false N141 0.573,0.125 0.885,0.323 0.313,0.198 10 false *a 0.625,1.854 0.938,2.052 0.313,0.198 10 false *b 1.625,0.198 1.938,0.396 0.313,0.198 10 false B 2.646,1.115 2.958,1.313 0.313,0.198 10 false 3a 2.427,2.417 2.74,2.615 0.313,0.198 10 false 1a 0.802,2.396 1.302,2.74 0.5,0.344 10 false GPS
*a Front view of wire harness connector
(to Navigation Antenna Assembly)
*b Front view of wire harness connector
(to Wire Harness)


Disconnect the antenna cord sub-assembly from the navigation antenna assembly connector.


b.

Disconnect the antenna cord sub-assembly from the wire harness connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-3 - N141-1 (GPS) Always Below 1 Ω
B-3a - N141-1a Always Below 1 Ω
B-3 or N141-1 (GPS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ANTENNA CORD SUB-ASSEMBLY - TELEPHONE TRANSCEIVER ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (ANTENNA CORD SUB-ASSEMBLY - TELEPHONE TRANSCEIVER ASSEMBLY)
a.
E409658C01
1.479,1.969 1.896,2.208 0.417,0.24 1.5,0.208 1.917,0.458 0.417,0.25 1.865,1.115 2.156,0.833 2.156,0.833 2.292,0.833 true 1.781,2.802 2.125,2.458 2.125,2.458 2.26,2.458 true 1.719,1.188 1.052,0.875 1.052,0.875 0.927,0.875 true 1.625,2.885 1.073,2.5 1.073,2.5 0.948,2.5 true 0.688,0.198 1,0.396 0.313,0.198 10 false *a 0.708,1.885 1.021,2.083 0.313,0.198 10 false *b 1.521,2 2.177,2.396 0.656,0.396 10 false N140 2.313,2.375 2.969,2.771 0.656,0.396 10 false 1a 2.302,0.719 2.958,1.115 0.656,0.396 10 false 1a 1.552,0.25 2.208,0.646 0.656,0.396 10 false N141 0.604,0.813 1.26,1.208 0.656,0.396 10 false GPS 0.583,2.427 1.24,2.823 0.656,0.396 10 false ANT2
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Telephone Transceiver Assembly)


Disconnect the antenna cord sub-assembly connector.


b.

Disconnect the telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N141-1 (GPS) - N140-1 (ANT2) Always Below 1 Ω
N141-1a - N140-1a Always Below 1 Ω
N141-1 (GPS) or N140-1 (ANT2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for LHD)>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.INSPECT NAVIGATION ANTENNA ASSEMBLY


Result:
Proceed to
OK
NG



OK

7.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

7.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.
E418056C01
1.51,1.76 1.927,2 0.417,0.24 1.469,0.156 1.885,0.396 0.417,0.24 1.521,3.167 1.938,3.406 0.417,0.24 1.865,0.813 2.448,1.208 2.448,1.208 2.604,1.208 true 2.333,2.563 2.49,2.948 2.49,2.948 2.688,2.958 true 1.635,3.979 1.198,3.656 1.198,3.656 1.052,3.656 true 2.073,2.563 1.958,2.917 1.958,2.917 1.813,2.917 true 1.802,4.052 2.198,4.271 2.198,4.271 2.323,4.271 true 1.573,3.208 2.073,3.552 0.5,0.344 10 false N141 0.573,0.125 0.885,0.323 0.313,0.198 10 false *a 0.604,1.688 0.917,1.885 0.313,0.198 10 false *b 1.625,0.198 1.938,0.396 0.313,0.198 10 false B 2.646,1.115 2.958,1.313 0.313,0.198 10 false 3a 0.729,3.594 1.229,3.938 0.5,0.344 10 false GPS 1.667,1.802 1.979,2 0.313,0.198 10 false C 0.604,3.146 0.917,3.344 0.313,0.198 10 false *c 2.396,4.198 2.896,4.542 0.5,0.344 10 false 1a 2.76,2.896 3.26,3.24 0.5,0.344 10 false 6a 1.615,2.833 2.115,3.177 0.5,0.344 10 false 5a
*a Front view of wire harness connector
(to Navigation Antenna Assembly)
*b Front view of wire harness connector
(to Antenna Divider)
*c Front view of wire harness connector
(to Wire Harness)


Disconnect the antenna cord sub-assembly from the navigation antenna assembly connector.


b.

Disconnect the antenna cord sub-assembly from the antenna divider connector.


c.

Disconnect the antenna cord sub-assembly from the wire harness connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-3 - C-6 Always Below 1 Ω
C-5 - N141-1(GPS) Always Below 1 Ω
B-3a - C-6a Always Below 1 Ω
C-5a - N141-1a Always Below 1 Ω
B-3 or C-6 - Body ground Always 10 kΩ or higher
C-5 or N141-1 (GPS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ANTENNA CORD SUB-ASSEMBLY - TELEPHONE TRANSCEIVER ASSEMBLY)

NG

8.CHECK HARNESS AND CONNECTOR (ANTENNA CORD SUB-ASSEMBLY - TELEPHONE TRANSCEIVER ASSEMBLY)
a.
E409658C01
1.479,1.969 1.896,2.208 0.417,0.24 1.5,0.208 1.917,0.458 0.417,0.25 1.865,1.115 2.156,0.833 2.156,0.833 2.292,0.833 true 1.781,2.802 2.125,2.458 2.125,2.458 2.26,2.458 true 1.719,1.188 1.052,0.875 1.052,0.875 0.927,0.875 true 1.625,2.885 1.073,2.5 1.073,2.5 0.948,2.5 true 0.688,0.198 1,0.396 0.313,0.198 10 false *a 0.708,1.885 1.021,2.083 0.313,0.198 10 false *b 1.521,2 2.177,2.396 0.656,0.396 10 false N140 2.313,2.375 2.969,2.771 0.656,0.396 10 false 1a 2.302,0.719 2.958,1.115 0.656,0.396 10 false 1a 1.552,0.25 2.208,0.646 0.656,0.396 10 false N141 0.604,0.813 1.26,1.208 0.656,0.396 10 false GPS 0.583,2.427 1.24,2.823 0.656,0.396 10 false ANT2
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Telephone Transceiver Assembly)


Disconnect the antenna cord sub-assembly connector.


b.

Disconnect the telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N141-1 (GPS) - N140-1 (ANT2) Always Below 1 Ω
N141-1a - N140-1a Always Below 1 Ω
N141-1 (GPS) or N140-1 (ANT2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT ANTENNA DIVIDER

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

9.INSPECT ANTENNA DIVIDER
a.
E241596C20
1.125,1.417 0.979,1.76 0.979,1.76 0.781,1.76 true 1.406,1.427 1.49,1.771 1.49,1.771 1.74,1.771 true 0.573,1.677 1,1.854 0.427,0.177 10 false 6a 1.813,1.688 2.24,1.865 0.427,0.177 10 false 5a 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a
*a Component without harness connected
(Antenna Divider)


Remove the antenna divider.

Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 - 6 Always Below 1 Ω
5a - 6a Always Below 1 Ω
5 - 5a Always 10 kΩ or higher
6 - 6a Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

10.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for LHD)>REMOVAL


Result:
Proceed to
NEXT



NEXT