The main body ECU (multiplex network body ECU) controls the operation of the following lights:
Map light sub-assembly*2, *5
Map light assembly*3, *4
No. 1 room light assembly (for Front)*3
No. 1 room light assembly (for Rear)*3
*2: for LED Type
*3: for Bulb Type
*4: w/o Overhead Console
*5: w/ Overhead Console
except Wagon for LED Type
for Bulb Type
for Wagon
w/ Entry and Start System:
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Perform the Active Test according to the display on the GTS.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Illuminated Entry System | Turns on the lights that are controlled by the illuminated entry system* | OFF or ON | Perform the Active Test with the DOOR switch is on. |
| Tester Display |
|---|
| Illuminated Entry System |
*: Refer to Operation Check for the lights that are controlled by the illuminated entry system.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>OPERATION CHECK
Map light sub-assembly and transponder key coil turn on or off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: except Wagon for LED Type
*2: for Wagon
*3: w/ Telematics System
*4: w/o Telematics System
*5: for Bulb Type
*6: w/o Overhead Console Box
*7: w/ Overhead Console Box
Disconnect the a14*1, a22*2*3 or a23*2*4 map light sub-assembly connector.
Disconnect the a12*5 map light assembly*6 or map light sub-assembly*7 connector.
Disconnect the a16 No. 1 room light assembly (for Front) connector.*5
Disconnect the Z4 No. 1 room light assembly (for Rear) connector.*5
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a14-4 (LM2) - 3B-29 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: w/ Telematics System *2: w/o Telematics System |
||
| a22-1 (DOOR) - 3B-29*1 | Always | Below 1 Ω |
| a23-3 (DOOR) - 3B-29*2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a12-2 (LM2) - 3B-29 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-29 - A-1 (ILE) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D