Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2019.06–2021.07
RM35X0E _56 Audio / Visual / Telematics _078379 NAVIGATION / MULTI INFO DISPLAY _0380999 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Mute Signal Circuit between Stereo Component Amplifier and Telematics Transceiver  


DESCRIPTION

The DCM (telephone transceiver assembly) sends a mute signal to the stereo component amplifier assembly.

The stereo component amplifier assembly controls the volume according to the mute signal from the DCM (telephone transceiver assembly).

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source. If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E380010E26
1,1.531 1.458,1.729 0.458,0.198 10 false N169 1,1.729 2.74,2.094 1.74,0.365 10 false Stereo Component Amplifier Assembly 4.969,0.781 5.208,0.99 0.24,0.208 10 false 17 2.052,0.771 2.281,0.958 0.229,0.188 10 false 24 1.521,0.927 1.979,1.125 0.458,0.198 10 false TMUT 5.292,0.896 5.781,1.094 0.49,0.198 10 false MUTE 4.99,1.531 5.448,1.729 0.458,0.198 10 false N74 5,1.719 6.771,2.104 1.771,0.385 10 false DCM (Telephone Transceiver Assembly)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the DCM (telephone transceiver assembly), make sure to replace it with a new one.


HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.INSPECT DCM (TELEPHONE TRANSCEIVER ASSEMBLY)
a.
E283621C19
1.458,0.208 1.948,0.469 0.49,0.26 1.042,0.365 1.292,0.365 1.292,0.365 1.458,1.198 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.583,0.25 1.979,0.448 0.396,0.198 10 false N74 0.615,0.271 1.177,0.469 0.563,0.198 10 false MUTE
*a Component with harness connected
(DCM [Telephone Transceiver Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N74-17 (MUTE) - Body ground Ignition switch ACC
Audio system playing
→ Emergency call mode
2.0 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - DCM [TELEPHONE TRANSCEIVER ASSEMBLY])
2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - DCM [TELEPHONE TRANSCEIVER ASSEMBLY])
a.

Disconnect the N169 stereo component amplifier assembly connector.


b.

Disconnect the N74 DCM (telephone transceiver assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N169-24 (TMUT) - N74-17 (MUTE) Always Below 1 Ω
N169-24 (TMUT) or N74-17 (MUTE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)
a.
E418276C01
1.5,0.75 1.917,1 0.417,0.25 1.979,2.063 2.188,0.885 2.188,0.885 2.396,0.885 true 0.188,0.167 0.354,0.323 0.167,0.156 10 false *a 2.458,0.813 2.885,0.969 0.427,0.156 10 false MUTE 1.604,0.792 1.948,0.99 0.344,0.198 10 false N74
*a Front view of wire harness connector
(to DCM [Telephone Transceiver Assembly])


Disconnect the DCM (telephone transceiver assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N74-17 (MUTE) - Body ground Ignition switch ACC 2.0 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE DCM (TELEPHONE TRANSCEIVER ASSEMBLY)

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY