Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2019.06–2021.07
RM35X0E _56 Audio / Visual / Telematics _078377 AUDIO / VIDEO _0385463 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Mute Signal Circuit between Radio Receiver and Telematics Transceiver  


DESCRIPTION

The DCM (telematics transceiver) sends a mute signal to the radio and display receiver assembly.

The radio and display receiver assembly controls the volume according to the mute signal from the DCM (telematics transceiver).

WIRING DIAGRAM

E419879E01
1.271,1.031 1.885,1.229 0.615,0.198 10 false TMUT 1.729,0.917 2.344,1.115 0.615,0.198 10 false 3 5.292,0.917 5.906,1.115 0.615,0.198 10 false 17 5.531,1.021 6.146,1.219 0.615,0.198 10 false MUTE 0.688,1.917 1.302,2.115 0.615,0.198 10 false O7 0.677,2.083 1.885,2.573 1.208,0.49 10 false Radio and Display Receiver Assembly 5.115,2.063 7.031,2.354 1.917,0.292 10 false DCM (Telematics Transceiver) 5.115,1.896 5.729,2.094 0.615,0.198 10 false N74

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.


·

When replacing the DCM (telematics transceiver), make sure to replace it with a new one.



HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION


PROCEDURE

1.INSPECT DCM (TELEMATICS TRANSCEIVER)
a.
E366538C20
1.5,0.802 1.896,1.052 0.396,0.25 1.396,1.896 1.021,0.906 true 0.188,0.125 0.5,0.323 0.313,0.198 10 false *a 0.792,0.708 1.302,0.917 0.51,0.208 10 false MUTE 1.594,0.833 1.906,1.031 0.313,0.198 10 false N74
*a Component with harness connected
(DCM [Telematics Transceiver])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N74-17 (MUTE) - Body ground Ignition switch ACC
Audio system playing
→ Emergency call mode
2.0 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])
a.

Disconnect the O7 radio and display receiver assembly connector.


b.

Disconnect the N74 DCM (telematics transceiver) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O7-3 (TMUT) - N74-17 (MUTE) Always Below 1 Ω
O7-3 (TMUT) or N74-17 (MUTE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (OUTPUT SIGNAL)
a.
E419880C01
1.479,0.719 1.969,1.01 0.49,0.292 1.99,2.083 2.167,2.583 true 0.188,0.167 0.354,0.323 0.167,0.156 10 false *a 2.031,2.635 2.458,2.792 0.427,0.156 10 false MUTE 1.604,0.771 1.948,0.969 0.344,0.198 10 false N74
*a Front view of wire harness connector
(to DCM [Telematics Transceiver])


Disconnect the DCM (telematics transceiver) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N74-17 (MUTE) - Body ground Ignition switch ACC 2.0 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY