Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM › from 2019.06
RM35X0E _58 Vehicle Interior _078601 SEAT _0396712 FRONT POWER SEAT CONTROL SYSTEM D

SEAT  FRONT POWER SEAT CONTROL SYSTEM  OPERATION CHECK  


CHECK POWER SEAT FUNCTION


E421931C01
2.594,1.135 2.896,0.292 2.896,0.292 3.021,0.292 true 3,1.75 3.146,1.917 3.146,1.917 3.26,1.917 true 1.365,2.104 0.906,1.646 0.906,1.646 0.781,1.646 true 2.729,2.646 2.563,2.646 2.563,2.646 2.396,2.51 true 2.104,2.188 2.833,1.26 2.833,1.26 2.958,1.26 true 4.604,1.125 4.25,0.458 4.25,0.458 4.125,0.458 true 5.969,2.104 6.188,1.573 6.188,1.573 6.313,1.573 true 4.583,2.625 4.708,2.625 4.708,2.625 4.875,2.479 true 3.958,1.958 4.083,1.958 4.083,1.958 4.344,1.729 true 5.25,2.208 6.313,1.135 6.313,1.135 6.438,1.135 true 0.208,0.083 0.49,0.281 0.281,0.198 12 false *A 3.833,0.094 4.115,0.313 0.281,0.219 12 false *B 2.76,2.563 2.948,2.74 0.188,0.177 10 false *a 3.021,1.198 3.208,1.365 0.188,0.167 10 false *1 3.063,0.208 3.25,0.385 0.188,0.177 10 false *b 3.302,1.854 3.49,2.031 0.188,0.177 10 false *c 0.604,1.563 0.792,1.74 0.188,0.177 10 false *d 6.479,1.063 6.646,1.24 0.167,0.177 10 false *1 6.365,1.49 6.552,1.667 0.188,0.177 10 false *d 4.406,2.531 4.594,2.708 0.188,0.177 10 false *a 3.771,1.875 3.958,2.052 0.188,0.177 10 false *c 3.958,0.375 4.146,0.552 0.188,0.177 10 false *b
*A for LHD *B for RHD
*1 Front power seat switch (driver seat) - -
*a Slide function *b Reclining function
*c Rear lifter function *d Front vertical function


a.

Check the basic functions.

i.

Operate the front power seat switch (driver seat) and check that the following seat functions operate properly:

·

Slide function

·

Reclining function

·

Rear lifter function

·

Front vertical function





CHECK POWER SEAT MOTOR (SLIDE, FRONT VERTICAL, REAR LIFTER AND RECLINING FUNCTIONS)


a.

Check the PTC operation inside the power seat motor.

NOTICE:
·

The inspection should be performed with the seat installed to the vehicle.

·

Perform the 4 steps below to check the full range of motion for each power seat function.



HINT:

The resistance of the PTC thermistor increases when a switch of the front power seat switch (driver seat) is held down even after the seat has been moved to the farthest possible position in one direction. If the resistance increases beyond a specified level, the current is shut off to prevent a short circuit.


i.

Choose a power seat function. Operate a switch of the front power seat switch (driver seat) and move the seat to the farthest possible position in one direction. Keep the seat in that position for approximately 60 seconds.


ii.

Operate the switch of the front power seat switch (driver seat) again and continue to try to move the seat in the same direction as in the previous step. Measure the time until the current is shut off (motor operation sound stops).

Standard:

4 to 90 seconds



iii.

After the current is shut off, release the switch of the front power seat switch (driver seat) and wait for approximately 60 seconds.


iv.

Operate a switch of the front power seat switch (driver seat) and move the seat in the opposite direction. Check that the motor operates.