The power slide door main switch signal is sent to the slide door motor unit LH (slide door ECU LH) and slide door motor unit RH (slide door ECU RH)*.
If the power slide door does not operate using any of the operations, a malfunction related to the power slide door operation conditions, power slide door main switch or power slide door sensor assembly LH circuit malfunction is a possible cause.
*: w/ Power Slide Door RH
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| *a | Front view of wire harness connector
(to Slide Door Motor Unit LH [Slide Door ECU LH]) |
Disconnect the slide door motor unit LH (slide door ECU LH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V10-1 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V10-3 (B) - Body ground | Always | 11 to 14 V |
| V10-6 (ECUB) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
Click hereVehicle Exterior>DOOR / HATCH>POWER SLIDE DOOR SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| PSD Main Switch | Power slide door main switch signal | ON or OFF | ON: Power slide door main switch on
OFF: Power slide door main switch off |
- |
| Tester Display |
|---|
| PSD Main Switch |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
Click hereVehicle Exterior>DOOR / HATCH>POWER SLIDE DOOR SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| PSD Touch Sensor | Power slide door sensor assembly LH signal | OFF, ON or Open | OFF: Power slide door sensor assembly LH not pressed
ON: Power slide door sensor assembly LH pressed Open: Power slide door sensor assembly LH open |
- |
| Tester Display |
|---|
| PSD Touch Sensor |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power slide door sensor assembly LH.
except Wagon:
Click hereVehicle Exterior>DOOR / HATCH>POWER SLIDE DOOR TOUCH SENSOR (except Wagon)>REMOVAL
for Wagon:
Click hereVehicle Exterior>DOOR / HATCH>POWER SLIDE DOOR TOUCH SENSOR (for Wagon)>REMOVAL
Inspect the power slide door sensor assembly LH.
except Wagon:
Click hereVehicle Exterior>DOOR / HATCH>POWER SLIDE DOOR TOUCH SENSOR (except Wagon)>INSPECTION
for Wagon:
Click hereVehicle Exterior>DOOR / HATCH>POWER SLIDE DOOR TOUCH SENSOR (for Wagon)>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (except Wagon) | B |
| NG (for Wagon) | C |
A
B
C
Disconnect the T4 slide door motor unit LH (slide door ECU LH) connector.
Disconnect the U6 power slide door sensor assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T4-4 (OSG) - U6-2 (OSG) | Always | Below 1 Ω |
| T4-1 (OS) - U6-1 (OS) | Always | Below 1 Ω |
| T4-4 (OSG) or U6-2 (OSG) - Body ground | Always | 10 kΩ or higher |
| T4-1 (OS) or U6-1 (OS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power slide door main switch.
Click hereVehicle Exterior>DOOR / HATCH>POWER SLIDE DOOR MAIN SWITCH>REMOVAL
Inspect the power slide door main switch.
Click hereVehicle Exterior>DOOR / HATCH>POWER SLIDE DOOR MAIN SWITCH>INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/o Power Slide Door RH) | A |
| OK (w/ Power Slide Door RH) | B |
| NG | C |
A
B
C
Disconnect the N51 power slide door main switch connector.
Disconnect the V10 slide door motor unit LH (slide door ECU LH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V10-2 (MSW) - N51-5 (MSW) | Always | Below 1 Ω |
| N51-2 (E) - Body ground | Always | 10 kΩ or higher |
| V10-2 (MSW) or N51-5 (MSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the W9 slide door motor unit RH (slide door ECU RH) connector.
Read the Data List according to the display on the GTS.
Click hereVehicle Exterior>DOOR / HATCH>POWER SLIDE DOOR SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| PSD Main Switch | Power slide door main switch signal | ON or OFF | ON: Power slide door main switch on
OFF: Power slide door main switch off |
- |
| Tester Display |
|---|
| PSD Main Switch |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N51 power slide door main switch connector.
Disconnect the V10 slide door motor unit LH (slide door ECU LH) connector.
Disconnect the W9 slide door motor unit RH (slide door ECU RH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V10-2 (MSW) - N51-5 (MSW) | Always | Below 1 Ω |
| N51-2 (E) - Body ground | Always | 10 kΩ or higher |
| V10-2 (MSW) or N51-5 (MSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG