Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › NITROGEN OXIDES SENSOR › 2019.06–2020.05
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0387404 NITROGEN OXIDES SENSOR A

1GD-FTV ENGINE CONTROL  NITROGEN OXIDES SENSOR  INSTALLATION  


PROCEDURE

Hide 89463D 1.INSTALL NO. 2 NITROGEN OXIDES SENSOR

a.
A443584

Install the No. 2 nitrogen oxides sensor to the sensor bracket with the 2 nuts, and attach the 2 clamps.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.
A443586C01
1.781,0.813 2.302,0.813 true 0.635,0.667 0.917,0.854 0.281,0.188 10 true *a 2.354,0.75 2.771,0.958 0.417,0.208 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, install the No. 2 nitrogen oxides sensor.

SST
09224-00012  

Torque:
Specified tightening torque : 55 N*m (561 kgf*cm, 41 ft.*lbf)

NOTICE:

Replace with a new part if it is dropped or if it receives a strong impact.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 255 mm (10.0 in.)): 49.2 N*m (502 kgf*cm, 36 ft.*lbf)




c.
A443583

Install the sensor bracket to the vehicle body with the 2 bolts.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


d.

Connect the connector to the No. 2 nitrogen oxides sensor.


e.
A440865

Attach the 2 clamps and connect the No. 4 exhaust gas temperature sensor to the sensor bracket.


f.
A440864

Connect the connector to the No. 4 exhaust gas temperature sensor.


Hide 89463C 2.INSTALL NO. 1 NITROGEN OXIDES SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)

a.
A443582

Install the No. 1 nitrogen oxides sensor with the 2 nuts to the exhaust sensor clamp bracket, and attach the clamp (cable tie).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.
A443587C01
1.771,1.01 2.219,1.896 2.219,1.896 2.646,1.896 true 0.719,0.479 1.031,0.635 0.313,0.156 10 false *a 2.719,1.823 3.177,2.021 0.458,0.198 10 false SST
*a Torque Wrench Fulcrum Length


Using SST, install the No. 1 nitrogen oxides sensor.

SST
09224-00012  

Torque:
Specified tightening torque : 55 N*m (561 kgf*cm, 41 ft.*lbf)

NOTICE:

Replace with a new part if it is dropped or if it receives a strong impact.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 255 mm (10.0 in.)): 49.2 N*m (502 kgf*cm, 36 ft.*lbf)




Hide 25051 3.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/ Exhaust Gas Temperature Sensor for EGR)

Hide 89463C 4.CONNECT NO. 1 NITROGEN OXIDES SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)

a.
A443569

Attach the 2 clamps and connect the No. 1 nitrogen oxides sensor.


b.

Install the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


c.

Connect the connector to the No. 1 nitrogen oxides sensor.