Home › Drivetrain › AC60E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV for EGR with Exhaust Gas Temperature Sensor) › 2019.06–2021.07
RM35X0E _52 Drivetrain _078741 AC60E AUTOMATIC TRANSMISSION / TRANSAXLE _0398020 AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV for EGR with Exhaust Gas Temperature Sensor) D

AC60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV for EGR with Exhaust Gas Temperature Sensor)  DIAGNOSIS SYSTEM  


EURO-OBD


a.

When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, the vehicle must be connected to an OBD scan tool (complying with ISO 15765-4). Various data output from the vehicle's ECM can then be read.


b.
C201372

Euro-OBD regulations require that the vehicle's on-board computer illuminate the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:

i.

The emission control system/components.


ii.

The powertrain control components (which affect vehicle emissions).


iii.

The computer itself.

In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are stored in the ECM memory.

If the malfunction does not reoccur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain stored in the ECM memory.



c.

To check DTCs, connect the GTS or OBD scan tool to the Data Link Connector 3 (DLC3) of the vehicle.

The scan tool displays DTCs, the freeze frame data and a variety of engine data.

The DTCs and freeze frame data can be cleared using the scan tool.

Click hereDrivetrain>AC60E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV for EGR with Exhaust Gas Temperature Sensor)>DTC CHECK / CLEAR



NORMAL MODE AND CHECK MODE


a.

The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2 trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1 trip detection logic" is used for simulating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent malfunctions.



2 TRIP DETECTION LOGIC


a.

When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the next drive cycle, the MIL is illuminated (2nd trip).



FREEZE FRAME DATA


a.

The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


b.
A103809E88
2.354,0.135 3.229,0.302 0.875,0.167 10 DTC stored 1.271,1.031 2.052,1.208 0.781,0.177 10 0.5 seconds 0.323,1.031 1.104,1.229 0.781,0.198 10 0.5 seconds 0.354,2.792 2.688,2.948 2.333,0.156 10 Freeze frame data which can be read 2.25,1.031 3.031,1.229 0.781,0.198 10 0.5 seconds

The GTS records freeze frame data in 5 different instances: 1) 3 times before the DTC is stored, 2) once when the DTC is stored, and 3) once after the DTC is stored. These sets of data can be used to simulate the vehicle condition around the time when the malfunction occurred. The data may help in finding the cause of the malfunction, or in judging if the DTC was caused by a temporary malfunction.



MIL ILLUMINATION PATTERN


a.

MIL (Malfunction Indicator Lamp) displays according to the vehicle condition.

HINT:

MIL display depends on malfunction class of each DTC.

Malfunction Class Requirement
Class A Malfunction where exhaust gas components exceed the OBD threshold
Class B1 Malfunction where exhaust gas components may exceed the OBD threshold
Class B2 Malfunction where it is predicted that exhaust gas components will not reach a level that exceeds the OBD threshold
Class C Malfunction where it is predicted that exhaust gas components will not reach a level that exceeds the regulation value


A446861E04
2.094,3.042 3.042,3.385 3.042,3.385 3,3.042 false 2.479,3.031 3.021,3.365 false 1.448,3.01 1.49,3.333 false 0.771,2.99 0.542,3.365 false 0.365,0.5 2.021,0.719 1.656,0.219 10 false Engine switch on (IG) 4.24,0.542 5.615,0.74 1.375,0.198 10 false Engine ON 0.354,1.24 1.198,1.625 0.844,0.385 10 false (1): Bulb test 1.427,1.208 4.635,1.406 3.208,0.198 10 false (2): Readiness status 3.198,1.208 4.125,1.844 0.927,0.635 10 false (3): MIL status (Engine OFF) 5.604,1.177 6.563,1.813 0.958,0.635 10 false (4): MIL status (Engine ON) 0.115,0.063 2.177,0.5 2.063,0.438 10 false MIL Illumination Pattern: 0.156,2.042 0.396,2.594 0.24,0.552 10 false MIL ON 0.156,2.729 0.479,3.073 0.323,0.344 10 false MIL OFF 6.292,2.885 7.063,3.531 0.771,0.646 10 false Time [sec.] 4.219,3.385 6.625,3.74 2.406,0.354 10 false Example: In case of "No malfunction" 2.844,3.385 3.781,3.604 0.938,0.219 10 false 5 seconds 1.208,3.365 2.146,3.583 0.938,0.219 10 false 10 seconds 0.25,3.365 1.188,3.583 0.938,0.219 10 false 5 seconds


b.

Refer to below for the relation between MIL display of (1) to (4) and its description.

i.

(1): Bulb test

·

Bulb operational: MIL ON

·

Bulb non operational: MIL OFF


HINT:

If the MIL is not illuminated, check the MIL circuit.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>MIL Circuit



ii.

(2): Readiness status

A446862E02
1.979,0.823 3.354,1.021 1.375,0.198 10 false Readiness 5.375,0.823 6.51,1.167 1.135,0.344 10 false Readiness status 0.208,1.896 1.479,2.635 1.271,0.74 10 false Readiness "Ready" 1.854,1.844 4.677,2.479 2.823,0.635 10 false In case of the readiness for all monitored components is complete. 5.729,1.198 6.365,1.604 0.635,0.406 10 false Ready 5.656,3.302 6.531,3.698 0.875,0.396 10 false Not ready 5.667,2.771 6.5,3.219 0.833,0.448 10 false 5 seconds 5.646,4.854 6.479,5.302 0.833,0.448 10 false 5 seconds 0.354,3.896 1.333,4.604 0.979,0.708 10 false Readiness "Not Ready" 1.802,3.781 4.625,4.417 2.823,0.635 10 false In case of the readiness for one or more of the monitored components is not complete.

HINT:

There are some items that cannot be determined if the engine is not running during troubleshooting. Therefore, when the engine switch is normally turned on (IG), the MIL blinks 5 times to indicate "Not ready".

(Even though it indicates "Not ready", this is not a malfunction.)



iii.

(3): MIL status (Engine OFF)

HINT:
·

This sequence is repeated until the engine starts or the engine switch is turned off.

·

For "Class B1", the MIL status changes from Mode 3 to Mode 4 (continuous illumination) if the cumulative elapsed time exceeds 200 hours after it is detected.



A446863E04
0.635,1.083 1.708,1.281 1.073,0.198 10 false Class A 0.25,1.438 1.74,1.844 1.49,0.406 10 false Class B1 (200 hours or more) 0.375,2.604 1.667,3.156 1.292,0.552 10 false Class B1 (Less than 200 hours) 0.563,3.281 2.021,3.594 1.458,0.313 10 false Class B2 0.615,4.885 2.073,5.198 1.458,0.313 10 false Class C 0.656,0.292 1.427,0.49 0.771,0.198 10 false Class 3.76,0.271 5.292,0.469 1.531,0.198 10 false MIL status 2.021,0.948 2.938,1.146 0.917,0.198 10 false MIL ON 2.01,1.927 2.927,2.125 0.917,0.198 10 false MIL OFF 2,2.594 2.917,2.792 0.917,0.198 10 false MIL ON 2.052,4.385 2.969,4.583 0.917,0.198 10 false MIL ON 2.031,6.115 2.948,6.313 0.917,0.198 10 false MIL ON 1.99,3.479 2.906,3.677 0.917,0.198 10 false MIL OFF 2.031,5.333 2.948,5.531 0.917,0.198 10 false MIL OFF 2.01,7.042 2.927,7.24 0.917,0.198 10 false MIL OFF 3.021,3.792 4.396,3.99 1.375,0.198 10 false 5 seconds 3.771,3.792 5.146,3.99 1.375,0.198 10 false 5 seconds 3.594,5.604 4.969,5.802 1.375,0.198 10 false 5 seconds 3.396,7.292 4.771,7.49 1.375,0.198 10 false 5 seconds 2.833,5.594 4.208,5.792 1.375,0.198 10 false 3 seconds 2.656,7.292 4.031,7.49 1.375,0.198 10 false 1 second 0.5,6.521 1.625,7.125 1.125,0.604 10 false No malfunction 1.927,0.635 2.844,0.833 0.917,0.198 10 false Mode 4 1.896,2.375 2.813,2.573 0.917,0.198 10 false Mode 3 1.875,5.844 2.792,6.042 0.917,0.198 10 false Mode 1 1.865,4.104 2.781,4.302 0.917,0.198 10 false Mode 2


iv.

(4): MIL status (Engine ON)

HINT:

For "Class B1", the MIL status changes from Mode 3 to Mode 4 (continuous illumination) if the cumulative elapsed time exceeds 200 hours after it is detected.


A446864E04
0.813,1.167 1.885,1.365 1.073,0.198 10 false Class A 0.396,1.469 1.875,1.938 1.479,0.469 10 false Class B1 (200 hours or more) 0.448,2.604 1.76,3.208 1.313,0.604 10 false Class B1 (Less than 200 hours) 0.573,3.365 2.031,3.677 1.458,0.313 10 false Class B2 0.615,4.885 2.073,5.198 1.458,0.313 10 false Class C 3.583,0.219 5.115,0.417 1.531,0.198 10 false MIL status 0.792,0.219 2.323,0.417 1.531,0.198 10 false Class 2.781,0.625 4.313,0.823 1.531,0.198 10 false Engine ON 2.99,3.51 4.521,3.708 1.531,0.198 10 false 15 seconds 0.573,6.563 2.104,6.76 1.531,0.198 10 false No malfunction 2.021,1.99 3.552,2.188 1.531,0.198 10 false MIL OFF 2.042,1.135 3.573,1.333 1.531,0.198 10 false MIL ON 2.063,2.583 3.594,2.781 1.531,0.198 10 false MIL ON 2.01,4.427 3.542,4.625 1.531,0.198 10 false MIL ON 2.031,6.219 3.563,6.417 1.531,0.198 10 false MIL ON 2.042,3.365 3.573,3.563 1.531,0.198 10 false MIL OFF 2.031,7.083 3.563,7.281 1.531,0.198 10 false MIL OFF 1.958,0.583 2.875,0.781 0.917,0.198 10 false Mode 4 1.958,2.333 2.875,2.531 0.917,0.198 10 false Mode 3 1.969,4.104 2.885,4.302 0.917,0.198 10 false Mode 2 1.979,5.865 2.896,6.063 0.917,0.198 10 false Mode 1




CHECK DATA LINK CONNECTOR 3 (DLC3)