Home › Drivetrain › AC60E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV for EGR with Exhaust Gas Temperature Sensor) › 2019.06–2021.07
RM35X0E _52 Drivetrain _078741 AC60E AUTOMATIC TRANSMISSION / TRANSAXLE _0398020 AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV for EGR with Exhaust Gas Temperature Sensor) U

AC60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV for EGR with Exhaust Gas Temperature Sensor)  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and Transmission / Data List.


g.

Read the Data List according to the display on the GTS.

Powertrain > Engine and Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed
·

This is the current vehicle speed.

·

The vehicle speed is detected using the wheel speed sensors.

-

There is a delay in when the vehicle speed data is displayed.

Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.



Engine Speed Engine speed Min.: 0 rpm
Max.: 16383 rpm
·

50 to 400 rpm: Cranking

·

700 to 800 rpm: Idling with warm engine


When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed.
Mass Air Flow Sensor Air flow rate from mass air flow meter sub-assembly Min.: 0 gm/sec
Max.: 655.35 gm/sec
Idling:
·

0.5 to 15 gm/sec (EGR on)

·

10 to 21 gm/sec (EGR off)


Running without load (3000 rpm):
·

43 to 89 gm/sec (EGR on)

·

72 to 117 gm/sec (EGR off)


·

Based on the MAF, the ECM controls the fuel injection volume, injection timing, EGR, etc.

·

When a judgment is difficult, turn off the EGR system and confirm this value.


Intake Manifold Absolute Pressure Absolute pressure inside intake manifold Min.: 0 kPa
Max.: 2047.96 kPa
Idling:
·

93 to 105 kPa (EGR on)

·

93 to 107 kPa (EGR off)


Running without load (3000 rpm):
·

118 to 160 kPa (EGR on)

·

106 to 153 kPa (EGR off)


·

When the engine switch on (IG) or the vehicle is idling, the intake manifold absolute pressure and atmospheric pressure are approximately the same (standard atmospheric pressure = 101 kPa).

Above approximately 1500 rpm, the turbo becomes effective and the pressure becomes higher than atmospheric pressure.

·

Inspect while comparing with "Target Boost Pressure".

·

With the accelerator fully open, if the actual manifold absolute pressure (MAP) is low compared to the target boost pressure by at least 20 kPa for 5 seconds or more, a feeling of insufficient power will occur.

·

When a judgment is difficult, turn off the EGR system and confirm this value.


Intake Manifold Absolute Pressure Supported Intake manifold absolute pressure support Unsupp or Supp -
·

Supp: The item is supported by the vehicle.

·

Unsupp: The monitor is not supported by the vehicle.


Coolant Temperature Engine coolant temperature Min.: -40°C (-40°F)
Max.: 215°C (419°F)
After warming up engine: 70 to 90°C (158 to 194°F)
·

If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.

·

After a long soak, the coolant temperature, intake air temperature and ambient temperature are approximately equal.


Battery Voltage Battery voltage Min.: 0 V
Max.: 65.5 V
11 to 14 V: Engine switch on (IG) -
Accel Position Accelerator position status Min.: 0%
Max.: 100%
·

Accelerator pedal released:

0%

·

Accelerator pedal fully depressed:

100%


·

"Accel Position" is the accelerator opening amount (%) for engine control use.

·

When the accelerator pedal position sensor output itself (Accel Sens. No.1 Volt %, Accel Sens. No.2 Volt %) is in the normal range, another actuator malfunction has caused the fail-safe function to restrict the accelerator.

·

Without cruise, ECT or VSC requests, and without accelerator restriction by the fail-safe function, this is adjusted in proportion to the amount the accelerator pedal is depressed by the driver.

·

Accelerator pedal released: 0%

·

Accelerator pedal fully depressed: 100%


Actual Throttle Position Bank 1 Actual throttle position Min.: 0%
Max.: 100%
Idling after engine warmed-up: 0 to 92% Closing percentage of the throttle valve.
·

Fully closed: 0%.

·

Fully open: 100%.

HINT:

There is no connection with the accelerator. However, under full load, the throttle is usually fully open (100%).



Symptoms when out of range:
·

Stuck closed: Engine stall, difficult to start, lack of power, black smoke, rough idle

·

Stuck open: Loud turbocharging sound, bad vibration when engine is stopped

·

When ECM detects a malfunction of the diesel throttle (MIL on), engine power is restricted so that the vehicle can drive with a maximum speed of 80 to 100 km/h.


Target Throttle Position Bank 1 Target throttle position Min.: 0%
Max.: 100%
·

Throttle valve fully closed: 0%

·

Throttle valve fully opened: 100%


If there is a malfunction of the throttle actuator, compare the target and actual throttle position values for troubleshooting.
Actual Throttle Position Bank 1 Supported Actual throttle position support Unsupp or Supp -
·

Supp: The item is supported by the vehicle.

·

Unsupp: The monitor is not supported by the vehicle.


Actual Throttle Position Bank 2 Supported Actual No. 2 throttle position support Unsupp or Supp -
·

Supp: The item is supported by the vehicle.

·

Unsupp: The monitor is not supported by the vehicle.


Target Throttle Position Bank 1 Supported Target throttle position support Unsupp or Supp -
·

Supp: The item is supported by the vehicle.

·

Unsupp: The monitor is not supported by the vehicle.


Target Throttle Position Bank 2 Supported Target throttle position (No. 2) support Unsupp or Supp -
·

Supp: The item is supported by the vehicle.

·

Unsupp: The monitor is not supported by the vehicle.


Starter SW Starter switch signal ON or OFF
·

ON: Starter operating

·

OFF: Starter not operating


-
Neutral Position SW Park/neutral position switch status ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
HINT:

When the failure still occurs even after adjusting these parts, refer to DTC P070513 or P070562*.


Stop Light SW Stop light switch ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
NT Sensor Speed Input turbine speed Min.: 0 rpm
Max.: 12750 rpm
·

Lock-up on (after warming up the engine): Value from transmission revolution sensor (NT) equal to engine speed

·

Lock-up off (idling with shift lever in N): Value from transmission revolution sensor (NT) nearly equal to engine speed


Data is displayed in increments of 50 rpm.
Speed (SP2) Output shaft speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
0 km/h (0 mph): Vehicle stopped (equal to vehicle speed) -
SP2 Sensor Voltage Transmission revolution sensor (SP2) sensor voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Engine idling -
Shift SW Status (P Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
HINT:

When the failure still occurs even after adjusting these parts, refer to DTC P070513 or P070562*.


Shift SW Status (R Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
HINT:

When the failure still occurs even after adjusting these parts, refer to DTC P070513 or P070562*.


Shift SW Status (N Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
HINT:

When the failure still occurs even after adjusting these parts, refer to DTC P070513 or P070562*.


Sport Shift Up SW Sport shift up switch status ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not held in "+" (up-shift)


-
Sport Shift Down SW Sport shift up switch status ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not held in "-" (down-shift)


-
Shift SW Status (S Range) Sport mode select switch status ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Shift SW Status (D Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in D, S, "+" or "-"

·

OFF: Shift lever not in D, S, "+" or "-"


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
HINT:

When the failure still occurs even after adjusting these parts, refer to DTC P070513 or P070562*.


A/T Oil Temperature No.1 No. 1 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

Approx. 80°C (176°F): After stall test

·

Equal to ambient temperature when cold soak


If the value -40°C (-40°F) or 150°C (302°F), No. 1 ATF temperature sensor circuit is open or shorted.
A/T Oil Temperature No.2 No. 2 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

Approx. 80°C (176°F): After stall test

·

Equal to ambient temperature when cold soak


If the value -40°C (-40°F) or 150°C (302°F), No. 2 ATF temperature sensor circuit is open or shorted.
ATF Thermal Degradation Estimate Estimated value of ATF thermal degradation Min.: 0
Max.: 65535
- If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate", thermal degradation of the ATF is suspected.
Perform ATF Thermal Degradation Estimate Reset after replacing the ATF.
Torque Converter Temperature Raise History Torque converter temperature raise history status Min.: 0
Max.: 255
- -
NT Sensor Voltage Transmission revolution sensor (NT) output voltage Min.: 0.000 V
Max.: 4.999 V
0.1 to 1.9 V: Engine idling -
Lock Up Status Lock up status ON or OFF
·

ON: Lock-up operating

·

OFF: Lock-up not operating


-
Shift Status ECM gear shift command 1st, 2nd, 3rd, 4th, 5th or 6th Same as actual gear -
Solenoid (SLT) Shift solenoid valve SLT status ON or OFF
·

ON: Shift solenoid valve SLT operating

·

OFF: Shift solenoid valve SLT not operating


-
Solenoid (SLU) Shift solenoid valve SLU status ON or OFF
·

ON: Lock-up permitted

·

OFF: Lock-up not permitted


-
Solenoid (SL1) Shift solenoid valve SL1 status ON or OFF
·

ON: Shift solenoid valve SL1 operating

·

OFF: Shift solenoid valve SL1 not operating


The value of this item only changes when performing an Active Test.
Solenoid (SL2) Shift solenoid valve SL2 status ON or OFF
·

ON: Shift solenoid valve SL2 operating

·

OFF: Shift solenoid valve SL2 not operating


The value of this item only changes when performing an Active Test.
Solenoid (SL3) Shift solenoid valve SL3 status ON or OFF
·

ON: Shift solenoid valve SL3 operating

·

OFF: Shift solenoid valve SL3 not operating


The value of this item only changes when performing an Active Test.
Solenoid (SL4) Shift solenoid valve SL4 status ON or OFF
·

ON: Shift solenoid valve SL4 operating

·

OFF: Shift solenoid valve SL4 not operating


The value of this item only changes when performing an Active Test.
Solenoid (SL) Shift solenoid valve SL status ON or OFF
·

ON: Lock-up permitted

·

OFF: Lock-up not permitted


-
HINT:

*: Refer to DTC P070513 or P070562.

Click hereDrivetrain>AC60E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV for EGR with Exhaust Gas Temperature Sensor)>P070513




ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and Transmission / Active Test.


g.

Perform the Active Test according to the display on the GTS.

Powertrain > Engine and Transmission > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the TC Terminal Connects and disconnects TC and TE1.
(changes to the fluid temperature detection mode)
ON/OFF
[Vehicle Condition]
·

Engine switch on (IG)

·

Vehicle stopped


Control the Shift Position Operates the shift solenoid valves to allow gears to be selected manually. 1st/2nd/3rd/4th/5th/6th
Start/Stop
Can be used to check the operation of the shift solenoid valves.
Up-shifts and down-shifts should be performed consecutively. A 10 second interval is required between gear changes.
Do not down-shift at high speeds. Doing so will damage the automatic transmission.
[Vehicle Condition]

50 km/h (31 mph) or less


Activate the Solenoid (SLU) Operates shift solenoid valve SLU ON/OFF
[Vehicle Condition]
·

Engine switch on (IG)

·

Engine stopped

·

Shift lever in P or N


HINT:

When the Active Test cannot be performed, turn the engine switch off and wait for 3 minutes or more before attempting to perform the Active Test again.


Activate the Solenoid (SLT) Operates shift solenoid valve SLT to raise the line pressure. ON/OFF
HINT:

ON: No action (normal operation)

OFF: Line pressure up (When the Active Test of "Activate the Solenoid (SLT)" is performed, the ECM commands the shift solenoid valve SLT to turn off).


[Vehicle Condition]
·

Vehicle stopped

·

Engine idling


Activate the Lock Up Solenoid Controls the shift solenoid valves SLU and SL to set the automatic transmission to the lock-up condition. ON/OFF
Start/Stop
Can be used to check shift solenoid valves SLU and SL operation.
[Vehicle Condition]
·

Vehicle speed: 70 km/h (44 mph) or more

·

Gear: Highest gear

·

Throttle valve opening angle: Less than 20%


Activate the Solenoid (SL) Operates shift solenoid valve SL ON/OFF
[Vehicle Condition]
·

Engine switch on (IG)

·

Engine stopped

·

Shift lever in P or N


HINT:

When the Active Test cannot be performed, turn the engine switch off and wait for 3 minutes or more before attempting to perform the Active Test again.


Activate the Solenoid (SL1) Operates shift solenoid valve SL1 ON/OFF
[Vehicle Condition]
·

Engine switch on (IG)

·

Engine stopped

·

Shift lever in P or N


HINT:

When the Active Test cannot be performed, turn the engine switch off and wait for 3 minutes or more before attempting to perform the Active Test again.


Activate the Solenoid (SL2) Operates shift solenoid valve SL2 ON/OFF
[Vehicle Condition]
·

Engine switch on (IG)

·

Engine stopped

·

Shift lever in P or N


HINT:

When the Active Test cannot be performed, turn the engine switch off and wait for 3 minutes or more before attempting to perform the Active Test again.


Activate the Solenoid (SL3) Operates shift solenoid valve SL3 ON/OFF
[Vehicle Condition]
·

Engine switch on (IG)

·

Engine stopped

·

Shift lever in P or N


HINT:

When the Active Test cannot be performed, turn the engine switch off and wait for 3 minutes or more before attempting to perform the Active Test again.


Activate the Solenoid (SL4) Operates shift solenoid valve SL4 ON/OFF
[Vehicle Condition]
·

Engine switch on (IG)

·

Engine stopped

·

Shift lever in P or N


HINT:

When the Active Test cannot be performed, turn the engine switch off and wait for 3 minutes or more before attempting to perform the Active Test again.


The "Activate the Solenoid (SLT)" Active Test is performed to allow confirmation that the line pressure changes. The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test.

Click hereDrivetrain>AC60E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV for EGR with Exhaust Gas Temperature Sensor)>HYDRAULIC TEST

HINT:

Note that the pressure readings for the Active Test and Hydraulic Test are different.