Home › Drivetrain › AC60E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV for EGR with Exhaust Gas Temperature Sensor) › 2019.06–2021.07
RM35X0E _52 Drivetrain _078741 AC60E AUTOMATIC TRANSMISSION / TRANSAXLE _0398020 AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV for EGR with Exhaust Gas Temperature Sensor) J

AC60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV for EGR with Exhaust Gas Temperature Sensor)  Transmission Control Switch Circuit  


DESCRIPTION

After moving the shift lever to S, it is possible to switch the shift range between "1" (S1 range) and "6" (S6 range) using the transmission control switch.

Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" once lowers the shift range by one.

WIRING DIAGRAM

C318220E49
0.198,0.625 1.063,1.385 0.865,0.76 10 false from ECU-IG1 NO. 2 Fuse 1.719,2.646 3.896,3.167 2.177,0.521 10 false Transmission Control Switch (Shift Lock Control Unit Assembly) 1.719,2.49 2.031,2.688 0.313,0.198 10 false N61 2.073,0.49 2.385,0.688 0.313,0.198 10 false IG 2.063,1.854 2.375,2.042 0.313,0.188 10 false E 3.271,0.5 3.583,0.688 0.313,0.188 10 false S 3.031,1.177 3.646,1.375 0.615,0.198 10 false SFTU 3.031,1.854 3.646,2.052 0.615,0.198 10 false SFTD 5.521,0.5 5.833,0.688 0.313,0.188 10 false S 5.51,1.167 6.125,1.365 0.615,0.198 10 false SFTU 5.521,1.854 6.135,2.052 0.615,0.198 10 false SFTD 5.844,2.5 6.385,2.844 0.542,0.344 10 false N2 5.844,2.656 6.25,3.271 0.406,0.615 10 false ECM 1.854,0.49 2.01,0.688 0.156,0.198 10 false 4 1.865,1.854 2.177,2.052 0.313,0.198 10 false 2 3.5,1.854 3.813,2.052 0.313,0.198 10 false 3 3.5,1.177 3.813,1.375 0.313,0.198 10 false 1 3.479,0.51 3.792,0.708 0.313,0.198 10 false 5 5.25,0.49 5.563,0.688 0.313,0.198 10 false 13 5.25,1.167 5.563,1.365 0.313,0.198 10 false 21 5.25,1.854 5.563,2.052 0.313,0.198 10 false 20 6.25,1.01 6.708,1.208 0.458,0.198 10 false 12 V 6.25,1.688 6.708,1.885 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS (Shift SW Status (S Range))
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Shift SW Status (S Range).


e.

Read the Data List according to the display on the GTS.

Powertrain > Engine and Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (S Range) Sport mode select switch status ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Powertrain > Engine and Transmission > Data List
Tester Display
Shift SW Status (S Range)
50003 456 25

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

2.READ VALUE USING GTS (SPORT SHIFT UP SW AND SPORT SHIFT DOWN SW)

B

6.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
2.READ VALUE USING GTS (SPORT SHIFT UP SW AND SPORT SHIFT DOWN SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Sports Shift Up SW, Sports Shift Down SW.


e.

Read the Data List according to the display on the GTS.

Powertrain > Engine and Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sport Shift Up SW Sport shift up switch status ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not held in "+" (up-shift)


-
Sport Shift Down SW Sport shift down switch status ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not held in "-" (down-shift)


-
Powertrain > Engine and Transmission > Data List
Tester Display
Sport Shift Up SW
Sport Shift Down SW
50003 456 24,23

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

B

3.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
3.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.
C239095C48
1.292,1.729 1.646,1.313 true 2.698,1.729 2.313,1.302 true 1.979,1.729 1.958,1.333 true 0.198,0.167 0.51,0.365 0.313,0.198 10 false *a 1.969,1.781 2.125,1.979 0.156,0.198 10 false E 2.604,1.781 3.219,1.979 0.615,0.198 10 false SFTU 1.104,1.771 1.719,1.969 0.615,0.198 10 false SFTD
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SFTU) - 2 (E) Shift lever held in "+" Below 1 Ω
1 (SFTU) - 2 (E) Shift lever in S 10 kΩ or higher
3 (SFTD) - 2 (E) Shift lever held in "-" Below 1 Ω
3 (SFTD) - 2 (E) Shift lever in S 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)

NG

REPLACE TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)
a.
C267936C83
0.229,0.979 0.583,1.24 0.354,0.26 0.927,1.896 1.5,1.406 true 0.813,1.854 1.125,2.052 0.313,0.198 10 false E 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.302,1.031 0.76,1.229 0.458,0.198 10 false N61
*a Front view of wire harness connector
(to Transmission Control Switch (Shift Lock Control Unit Assembly))


Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N61-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
C318001C21
2.229,0.344 2.604,0.531 0.375,0.188 2.833,2.917 2.552,1.979 true 2,2.917 2.49,1.979 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 1.667,2.969 2.896,3.167 1.229,0.198 10 false 21 (SFTU) 2.583,2.969 3.302,3.177 0.719,0.208 10 false 20 (SFTD) 2.344,0.365 2.656,0.563 0.313,0.198 10 false N2
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-21 (SFTU) - Body ground Shift lever held in "+" Below 1 Ω
N2-21 (SFTU) - Body ground Shift lever in S 10 kΩ or higher
N2-20 (SFTD) - Body ground Shift lever held in "-" Below 1 Ω
N2-20 (SFTD) - Body ground Shift lever in S 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.
C239095C86
0.771,1.729 1.125,1.313 true 1.906,1.75 1.521,1.323 true 0.198,0.167 0.51,0.365 0.313,0.198 10 *a 1.906,1.802 2.375,2 0.469,0.198 10 IG 0.646,1.771 1.021,1.979 0.375,0.208 10 S
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in S Below 1 Ω
4 (IG) - 5 (S) Shift lever not in S 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)

NG

REPLACE TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)
a.
C267936C84
0.229,0.979 0.583,1.24 0.354,0.26 2.646,1.875 2,1.406 true 2.719,1.802 3.031,2 0.313,0.198 10 false IG 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.302,1.031 0.76,1.229 0.458,0.198 10 false N61
*a Front view of wire harness connector
(to Transmission Control Switch (Shift Lock Control Unit Assembly))


Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N61-4 (IG) - Body ground Engine switch on (IG) 11 to 14 V
N61-4 (IG) - Body ground Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Disconnect the transmission control switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N61-5 (S) - N2-13 (S) Always Below 1 Ω
N61-5 (S) - Body ground Always 10 kΩ or higher
N2-13 (S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR