The main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver communicate by direct line. If a malfunction occurs in this communication signal, B1247 is output by the main body ECU (multiplex network body ECU).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B1247 | Tire Pressure Monitor Receiver Communication Stop | Communication between the tire pressure warning ECU and receiver and main body ECU (multiplex network body ECU) is interrupted for 10 seconds or more. | ·
Tire pressure warning ECU and receiver ·
Wire harness or connector ·
Main body ECU (Multiplex network body ECU) |
This DTC is for main body ECU (multiplex network body ECU) |
When replacing the tire pressure warning ECU and receiver, read the transmitter IDs and number of the transmitters (4 or 5) stored in the old ECU using the GTS and write them down before removal.
It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.
| *A | w/o Entry and Start System and w/o Wireless Door Lock Control System, for GDH303L-RDTJY and GDH303L-RDTGY w/ Entry and Start System (for FMVSS138 Type) |
| *B | w/o Entry and Start System and w/ Wireless Door Lock Control System or for GDH303L-RDTJY and GDH303L-RDTGY w/ Entry and Start System (for ECE-R64 Type) |
| *a | Component with harness connected
(Tire Pressure Warning ECU and Receiver) |
| *b | GND |
Using an oscilloscope, check the waveform.
With the connector connected, check from the backside of the connector.
| Tester Connection | Tool Setting Range | Condition | Specified Condition |
|---|---|---|---|
| Z3-4 (RDA2) - Body ground | 5 V/DIV, 5 ms./DIV. | Ignition switch ON | Waveform generation |
| Tester Connection | Tool Setting Range | Condition | Specified Condition |
|---|---|---|---|
| Z30-4 (RDA) - Body ground | 5 V/DIV, 5 ms./DIV. | Ignition switch ON | Waveform generation |
| Result | Proceed to |
|---|---|
| Waveform is as shown in the illustration. (Waveform alternates between 10.5 V or higher and 0.5 V or less) | A |
| Waveform does not change from 10.5 V or higher | B |
| Waveform does not change from 0.5 V or less | C |
A
B
for Standard Roof:
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER (for Standard Roof)>REMOVAL
for High Roof:
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER (for High Roof)>REMOVAL
C
Disconnect the tire pressure warning ECU and receiver connector.
| *A | w/o Entry and Start System and w/o Wireless Door Lock Control System, for GDH303L-RDTJY and GDH303L-RDTGY w/ Entry and Start System (for FMVSS138 Type) |
| *B | w/o Entry and Start System and w/ Wireless Door Lock Control System or for GDH303L-RDTJY and GDH303L-RDTGY w/ Entry and Start System (for ECE-R64 Type) |
| *a | Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z3-4 (RDA2) - Body ground | Ignition switch ON | 10.5 V or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z30-4 (RDA) - Body ground | Ignition switch ON | 10.5 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for Standard Roof:
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER (for Standard Roof)>REMOVAL
for High Roof:
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER (for High Roof)>REMOVAL
NG
Turn the ignition switch off.
Disconnect the N20 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N20-10 (RDA) - Z3-4 (RDA2) | Always | Below 1 Ω |
| N20-10 (RDA) or Z3-4 (RDA2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N20-10 (RDA) - Z30-4 (RDA) | Always | Below 1 Ω |
| N20-10 (RDA) or Z30-4 (RDA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG